In my bathroom, the tip of the pivot rod which is connected to the stopper is broken. When the stopper goes down, it has no rod to hook to. Is it possible to re-use and re-adjust the existing pivot rod? If not, should I get a new one? Which name should I use to describe the hardware that I need when I go to the hardware store? If you have actually snapped the rod but have enough length to spare you should be able to move it forwards, however are you sure this has happened? The reason I ask is that I had similar symptoms, but all that had happened is that the rod had slipped back through the clevis strap so it no longer connected with the stopper. The clip holding it to the strap made it look like it was just broken, but I eventually figured it out. Admittedly, on mine there is no hook holding the rod to the stopper, it simply pushes the stopper up, and gravity lets it fall again when you pull the plunger up. This just happened to me, yes the little ball does slide on the rod, although it took a hammer to get it to move.

Pushing the ball down the rod 2 cm gave me enough rod for the stopper to start working again.Browse other questions tagged sink or ask your own question. Disassemble and Clean the Pop-Up Stopper Assembly Move everything from under the sink so you have room to work. Check to see that the horizontal pivot rod is connected to the clevis. Loosen the retaining nut that holds the horizontal pivot rod in place. Remove the horizontal pivot rod from the drainpipe. Mark the spot where the clevis is connected to the stopper rod with a permanent marker. Then loosen the clevis screw. Soak the clevis and horizontal pivot rod in mild cleaning solution or vinegar. Lift the stopper out of the drain. Inspect the rubber seal on the bottom of the stopper head. If the seal is cracked or brittle, the stopper should be replaced. If it's still in good condition, you can reuse it. Dip the stopper in mild cleaner or vinegar. Clean it thoroughly with a brush or an old toothbrush. Rinse the stopper and clean the clevis and horizontal pivot rod.

Reassemble and Adjust the Pop-Up Stopper Assembly Insert the stopper into the drain. Slide the clevis over the stopper rod and insert the horizontal pivot rod into the drainpipe. Tighten the retaining nut just enough to hold the horizontal pivot rod in place. Tighten the clevis screw where you marked it before. Test the stopper rod to ensure all the moving parts are reattached. The clevis, horizontal pivot rod and stopper should all move when the stopper rod is pulled. Tighten the retaining nut just enough so the stopper rod doesn't slide down. If the retaining nut is too tight, the horizontal pivot rod won't move. Loosen the clevis screw, and pull the stopper rod up. Slide the clevis up the stopper rod as far as you can. Tighten the clevis screw. The pop-up stopper should hold water now. If not, continue to adjust the retaining nut and the clevis until you get a good seal.Look behind the sink for the pivot rod. To plug the bathroom sink, you must pull up on the stopper lever behind the faucet.

The simple action of pulling the lever causes a series of parts to work together to lower the stopper. Pulling up the stopper lever raises the clevis. The clevis attaches to the back of the pivot rod, and the opposite end of the pivot rod attaches to the bottom of the drain stopper inside the drain. Raising the pivot rod lowers the stopper and plugs the sink. Cheap Teacup Maltese Puppies For Sale In IllinoisA broken pivot rod will not lower the stopper and must be replaced. Royal & Aqua Ombre Rhinestone & Tulle Lace Up Short Prom DressLook beneath the sink and behind the drain to find the pivot rod. Van Sewa Di MuarIt extends from the drain to the flat metal clevis rod attached to the bottom of the stopper lever.

A retaining nut and washer holds the pivot rod and pivot rod ball in the drain, and a clevis screw connects the rod to the stopper lever. Unscrew the retaining nut that holds the pivot rod inside the drain. Slide the nut and washer onto the original pivot rod. Pull the pivot rod out of the drain. Squeeze the spring clip holding the pivot rod to the clevis with your thumb and forefinger. This releases the tension on the clip and allows you to slide the rod out of the clip and the clevis. Slide the retaining nut and washer off the original pivot rod. Wipe the retaining nut and washer with a rag to clean any debris off these items. Wipe the thread and opening on the drain where the pivot rod inserts. Thread the washer and retaining nut onto a new pivot rod. Let the washer and nut rest against the pivot rod ball connected to the end of the pivot rod. Insert the pivot rod and pivot rod ball into the drain. Make sure the tip of the rod threads through the opening in the drain plug’s tail piece.

Slide the washer and nut against the threads in the drain. Hand-tighten the retaining nut onto the drain to hold the pivot rod in the drain. Squeeze the two sides of the clip together that held the original pivot rod to the clevis. Slip the clip around the clevis, lining the holes in the two sides of the clip with one of the holes in the clevis. Slide the opposite end of the pivot rod through the two sides of the clip and clevis. Release the clip to hold the pivot rod to the clevis. Test the placement of the pivot rod by pulling up on the stopper lever. If the drain plug does not close to your satisfaction, move the pivot rod to another hole in the clevis. Things You Will Need Rags Adjustable wrench References Lowes: Pop-Up Sink Stopper RepairThe Home Depot: Cleaning a Sink Stopper (Pop-Up)Don Vandervorts Home Tips: How to Fix a Bathtub or Sink Pop-up Stopper Photo Credits Digital Vision./Digital Vision/Getty Images Suggest a CorrectionWhen a pop-up drain stopper in a sink or bathtub stops working, how do you fix it?

This expert guide shows how drain stoppers work and how to repair them. Pop-ups are simple mechanical devices that use a system of links and levers to move a drain stoppers up and down to seal a sink bowl or bathtub. Bathroom sink pop-ups are raised and lowered with a lift knob or lever, usually located on or near the faucet body. The knob or lever is connected to a lift rod that is fastened to a flat, slotted bar called a “clevis.” The clevis is connected by a small spring clip to a pivot rod–and–ball assembly—a rod that runs through a rubber pivot ball and slopes slightly upward to the tailpiece of the stopper. This pushes the stopper up or lets it drop down into the drain body. Pushing the knob and the lift rod down causes the pivot rod to push the stopper up; pulling the knob causes the pivot rod to pull the stopper down. If you want to remove the assembly, you may be able to pull it right out. On a bathroom sink, it’s often necessary to remove the retaining nut and extract the pivot rod first.

You may have to twist the stopper to unhook it from the pivot rod. A bathtub pop-up is raised or lowered with a lever at the tub’s overflow plate. The lever operates a lift linkage that pulls on a spring. The spring pulls a rocker arm that raises and lowers the stopper (see the illustration). It is usually very simple to pull out the stopper and rocker arm linkage. Click here to buy pop-up drain stoppers online. Stoppers that don’t close can keep the drain or tub from filling properly and waste water. These kinds of stopper problems are mechanical and can be solved with simple adjustments. It’s easy to remove a tub stopper to check it for mechanical problems or blockage. 1. Simply grip the stopper body and pull it out of the drain along with the hinged rocker arm. 2. Clear the stopper and rocker arm of hair and debris. 3. Check the rubber seal for damage and, if necessary, replace it. Remove the old seal and slip on a new one if needed.

4. Reinstall the stopper and rocker arm. Make sure the flange is tightly seated and in good shape. (Older tubs may have corroded flanges.) For more, see Bathtub Pop-Up Repairs. Water may leak or refuse to drain around a sink pop-up for a number of reasons. If your sink pop-up won’t pop up or seat properly, fixing it is quite easy—usually just a matter of adjusting a few parts. The culprit is often a buildup of hair around the base of the stopper or the pivot rod mechanism. Or, the clevis may be out of adjustment (see illustration to identify the various parts). Here’s how to fix the problem: 1With a slight twist, try to lift out the stopper. If it seems to be linked to the mechanism below, reach under the sink and unscrew the pivot rod retaining nut and pull out the pivot rod to disengage it. 2Lift the stopper from the drain. Clean off all hair and debris. If the stopper is broken or its seal looks worn, replace it. 3Face the hole at the bottom of the stopper toward the pivot rod’s location, and drop the stopper back into the drain hole.

Insert the pivot rod so that it engages the hole in the bottom of the stopper, and tighten on the retaining nut with the stopper in its up position. When the drain is closed, the pivot rod should slope slightly uphill from the clevis to the tailpiece. 4Loosen the set screw on the clevis and adjust the strap up or down so that it operates the pivot rod to open and close the stopper. Retighten the set screw. 5If adjusting the clevis screw doesn’t help, reset the pivot rod by squeezing the spring clip and freeing the pivot rod. Move the clip up to the next clevis hole and insert the rod. You may need to keep tweaking this a little to find the right hole on the clevis. 6If water drips from around the pivot ball, tighten the retaining nut that holds the ball in place. You may also need to replace the gasket or washer (or both) inside the pivot ball-and-rod assembly. Keeping drains clear of hair, soap and shampoo residue, and other debris is one of the best ways to help keep pop-up stoppers in good working order.