Expert ReviewedHow to Bleed Brake Lines Three Parts:Getting ReadyBleeding the BrakesTesting the BrakesCommunity Q&A You are slowing down to stop at a traffic light only to find that your brakes are soft and the pedal is low. This could be a sign that air has crept into the brake lines. To fix this, it may be necessary to bleed your brakes. This is a two-man job that requires a coordinated effort. The result is a stiffer brake pedal and a more reactive braking system. Confirm you need to bleed the brake lines. The sinking brake pedal often does mean the brake lines need to be bled. However, it is very important to confirm that the sinking pedal is not caused by something else. Try this simple test when you are stopped and waiting at a red light. With your foot, keep an even pressure on the brake pedal. Does the pedal sink lower, even a little bit? If so, then you should have your car's brake system inspected by an ASE Certified Master Auto Technician to confirm the root cause is not something else.

If the pedal holds constant pressure, then there is no air in the system. A sinking brake pedal could also be caused by other things that could be very dangerous. For example, brake pedals can also sink if there is a hydraulic problem, like a failing master cylinder, a leaking rear wheel cylinder, a bad caliper or bad ABS. So it is important to rule out these dangerous possibilities via professional inspection before proceeding. Position your car on a flat surface. Take off any hubcaps and raise the car and secure it on jack stands. Remove all four wheels. Release the hood and locate the Master Cylinder brake fluid reservoir. Eliminate the old, dirty brake fluid that is present in the Master Cylinder Reservoir. Go to the right rear wheel, wipe off any dirt from the brake bleeder screw area and remove its rubber dust cap. Hold onto the box wrench while holding the plastic bottle. When the brake fluid becomes clear, direct your partner to hold the pedal to the floor.

Close the bleeder screw with the wrench and have your partner pump the pedal 3 times and hold it. Open up the bleeder screw briefly to allow the brake fluid to exit the rubber hose. Have your partner tell you when the brake pedal is on the floor, and, have him/her keep it there while you close the bleeder screw. Repeat this process two more times. (Remember periodically check the Master Cylinder fluid level, so it does not go dry!) After the third time, tighten the bleeder screw and repeat this process on the other three wheels and, in this order; Left Rear, Right Front and Left Front. Depending on the vehicle, the bleeding procedure will vary in which wheel is bled first, second and so on. The above sequence will work for a large portion of vehicles, however you should check with a website like Alldata or similar to verify bleeding sequence. In order to make sure your brakes are not spongy and there aren't any leaks in the system, perform this test when your are finished bleeding the brakes.

Get rid of any surplus brake fluid in a proper and safe manner. White Pomeranian Puppies For Sale Buffalo NyRemember that brake fluid is considered hazardous waste and therefore should never be poured down the sink or toilet, onto the ground in your yard, in the garbage, or down the sewer drain or septic tank.Poodle Toilet Seat[1] Talk with your local auto shop or look for a household hazardous waste (HHW) recycling collection site.Red Goldendoodle Puppies For Sale Nj Replace all four wheels and hand-tighten all the lug nuts. Go for a test drive to verify that the brakes are functioning correctly. Follow proper safety procedures when jacking up a vehicle. Always keep the brake fluid reservoir full. Avoid brake fluid coming in contact with rubber or plastic materials.

Bleed your vehicle’s brake lines every two years. Do not release the brake pedal until the bleeder screw is closed. Dirt particles can contaminate brake fluid and cause brakes to fail. Brake fluid will melt your car’s paint. Only use the brake fluid that is recommended for your make and model vehicle. I got a 94 honda accord. Recently ebrake light on the dash shows up even the ebrake handle is down. I tried to look at the switch on the ebrake and mess with it a little bit. Then the ebrake light comes off on the dash, but when I start pumping the pedal brakes it comes on again. Is there any problem in the brake pedal switch? I tried turn off the car then turn it on again the ebrake light went off but when I start pumping the brakes, it shows up again at the dash. Brake fluid is at maximum level. honda accord parking-brake brake-light If the light was shut off after pumping the foot brakes the issue was not the parking brake. The problem is in the regular braking system you use to stop the car, as such it needs immediate attention.

It may have been caused by something as simple as low brake fluid level. If the level is low either the system has a leak or the brake pads are worn to the point they should be replaced. If the fluid level is within the normal marks on the brake reservoir, the master cylinder may be failing. Many times in the early stages of master cylinder failure the brakes can be recovered by pumping the pedal. This will only work for so long before it catastrophically fails.Browse other questions tagged honda accord parking-brake brake-light or ask your own question.Wiper Product Info : Winter Wiper Info : Rv, Truck & Bus Wiper Info : Other Wiper Products : Wiper Washer Spray Pumps Rain Repelling Glass Treatment How to Change Wiper Blades Wiper Blade Installation Videos Beam Blades vs Standard Wipers Bulb Product Info : HID - OE Xenon HID How to Replace Bulbs About Eiko & Philips About W123 / H123 Visit Our Other Store : Note : Use vehicle search at top to avoid incorrect purchases