You might’ve heard that the hardest part of putting in a new faucet is getting the old one out, but that’s only true because today’s faucets install so easily! Removing an old faucet (and a pop-up drain assembly, too!) only takes a few minutes and a little elbow grease. Watch the how-to video Paint tray or shallow bucket 1. Clear out the space under your sink, and insert the paint tray or bucket beneath the pipes to catch the excess water. Keep the old towels close to absorb any spills. 2. Shut off the valves to the hot and cold water supply lines. Turn on the faucet to drain any excess water. For a single-handle faucet: 1. Under the sink, loosen the nut holding the top of the strap to the lift rod. Slide the strap and the metal clip off the horizontal rod. Unscrew the pivot nut and remove the horizontal rod from the back of the tail piece. 2. Use the adjustable wrench to disconnect the water supply lines running to the faucet. If you have flexible supply lines, you’ll likely be able to use them again.

3. Look underneath the sink to locate the mounting nut, which holds the faucet in place. Use a wrench to unscrew the nut. If the nut won’t budge, apply a little penetrating oil to the connection and let it sit for a few hours or overnight. 4. Once the mounting nut is removed, pull the old faucet out. If the faucet seems to stick to the sink or countertop, gently use a putty knife to help break the seal. Scrape off any old putty and wipe the surface clean with a damp cloth. For a two-handle faucet: 1. For sinks with separate handles for hot and cold water, use a wrench to disconnect the coupling nuts that connect the handles’ valves to the spout. Then, disconnect the two water supply valves. 2. Look underneath the sink to locate the mounting nuts, which hold the spout and handles in place. Use a wrench to unscrew the nuts. If the nuts won’t budge, apply a little penetrating oil to the connection and let it sit for a few hours or overnight. 3. Once the mounting nuts are removed, pull the old faucet out.

For a pop-up drain assembly:Parson Russell Terrier Puppies For Sale In Colorado 1. Beneath the sink, use your hand or a pipe wrench to unscrew the connection where the tailpiece enters the drain.Homes For Sale In Sao Miguel Azores 2. Use the channel lock pliers to unscrew the large nut at the bottom of the sink. Homes For Sale Gadsden Al 35901Pull the washer and gasket down, then push up on the tail piece to loosen the seal inside the sink. 3. You should be able to unscrew the sections above and below the sink and remove them. Need a new faucet? Here’s how to shop for one.How do you fix a dripping tub faucet? A dripping bathtub faucet is annoying and costly, due to the water it wastes.

Replacing the seats and seat washer fixes the leak. Use a shower stem socket and seat wrench for the project. Penetrating oil helps to remove stuck parts and thread sealant prevents leaks. How do you replace a bathtub faucet? How do you install a washerless bathtub faucet? How do you repair a bathtub faucet? Turn off the waterIf you have access to the shutoff valves that provide water to the tub close them. If you cannot access these valves, turn off the main water supply to the home.Remove handlesUse a thin, flat-blade screwdriver to remove the caps from the handles. Use a Phillips screwdriver to remove the screws that hold the handles in place. Pull on each handle to remove.Loosen stem nutsUse the stem socket to turn the stem nuts counterclockwise. Spray with penetrating oil if the nuts are difficult to remove. Let the oil stand for at least 15 minutes before loosening. Remove each stem from the faucet.Replace the seatsInsert the seat wrench into the seats and remove by turning counterclockwise.

Add thread sealant to the new seats. Use the seat wrench to insert and tighten the new seats.Replace seat washersThe rubber seat washers are at the end of the stem. Remove the screw that holds them in place. Assemble the faucetReturn the stems to the faucet and use the stem socket to tighten them. Replace the faucet handles and tighten the screws. Pop the handle caps back in place. How do you stop a dripping faucet? To fix a dripping faucet, dissemble the faucet, replace the O-ring and washer, and reassemble the faucet. If this doesn't work, you may have to tighten faucet parts, replace worn-out seals, clean a corroded valve seat, or fix the plumbing. How can a person fix a leaky bathtub faucet? To fix a leaky bathtub faucet, turn off the main water valve, remove the faucet handle and plate, remove the old O-ring and replace it with a new one and replace the faucet plate and handle. Most leaks are caused by a worn out O-ring. If this does not fix the leak, it may be due to a leaky pipe.

How do you repair a leaky Delta bathtub faucet? To repair a leaky Delta bathtub faucet, replace the worn rubber seats and springs. If the faucet has a handle for each temperature setting, feel the temperature of the water leaking from the spout to determine which handle needs to be repaired. Replacing a tub faucet involves removing the old faucet from the tub, replacing the old spout nipple with a new one and attaching a new faucet on the new nipple. Obtain a new faucet of the same style and size as the old one before attempting this task. On top of the new faucet, you need a screwdriver, Teflon tape, caulk, a new spout nipple and a pipe wrench. How does a toilet syphonic system work? How do you treat well water with bleach? What are some Craftsman shallow well pumps? How do you fix a leaky frost-proof exterior faucet? Approximately how much would it cost to have a well water pump replaced?How do you change a Roman tub faucet? Characterized by a long, thin, downward-curving neck, a Roman tub faucet sits on top of a bathtub.

There are three independent sections in this faucet, each of which are installed with their own separate hole. You need an Allen wrench and pliers to change a Roman tub faucet. What is the Roman numeral for one million? Shut off the water valveClose off the water valves to the bath. If these are not accessible, then the main water line to the house needs to be shut off first.Remove the set screws Using the Allen wrench, loosen the set screws located on the handles of the faucet. Remove the handles by pulling them up and away from the tub surface after the screw is taken out.Remove the retaining screw on the spoutTo remove the spout, unscrew the retaining screw located on the back of the spout. After this, you can remove the spout by simply pulling it up.Install the new spout Insert the new spout into the hole. Tighten the retaining screw with the Allen wrench. Install the handlesScrew the handles into place using the provided mounting hardware. Use plumber's putty on the surfaces that come into contact with the tub surface to protect it from external factors.

How do you fix a leaking tub faucet? To repair a leaking tub faucet, disassemble the faucet assembly and replace any worn or damaged washers, seals or gaskets. Worn washers, seals and gaskets are the culprit for many leaks, although not all. How do you paint a bathtub? To paint a bathtub, use a commercial lime remover to clean the tub, then wet-sand it to deglaze the finish before applying a dedicated tub and tile paint. The process takes about 8 hours, but requires 2 more days for the new finish to cure. How do you reglaze a bathtub? To reglaze a bathtub, take out the trim plumbing, caulking and grout from the tub, ensure that the area is well ventilated, clean the bathtub thoroughly, and apply a body filler in the tub. Then, prime the bathtub, apply glaze over it, and apply caulk and grout on the borders of the tub. Which planet in the solar system is named after the Roman messenger to the gods? Where do you buy replacement parts for vacuum pumps?