Moen creates a line of signature faucets for high end homes and commercial properties. Moen products are based around a replaceable cartridge system that is intended to be cleaned every three to five years. The cartridge system controls the water pressure and mixture of hot and cold water. When the cartridge becomes worn and builds up with calcium and lime deposits, the faucet may begin to leak or continuously drip even with the faucet in the off position. Shut the water main off before beginning any plumbing work that takes apart a sink or faucet. The water main is located beneath the sink or cabinets of the room you are working in. Locate two handles (sometimes one) connected to copper pipes or flexible metal tubing. Turn these counterclockwise 1/4 turn to reach the off position. Attach your hex key to the star shaped aperture located beneath the faucet handle for single handled faucets or beneath the spigot for double handle faucets. Turn the hex key counterclockwise until the spigot and handle for single handles comes apart, usually six to eight full turns.

For double handles, complete this step for each handle. Remove the handle and spigot to reveal the Moen cartridge system beneath. Use your pliers to turn the cartridge 1/4 turn counterclockwise to unlock it. Once the cartridge is unlocked you may gently remove it. Insert the new cartridge with your pliers, turning it clockwise to lock it into place. You will hear a small click when it is seated correctly. Reattach the spigot and handle using the hex key (clockwise several turns). Make sure the hex key is tightened at least six to eight turns to prevent leaks. Repeat this for each handle on double handles. Single handle faucets use part #1224 for replacement and double handled faucets use #1225. Moen cartridges are designed to be replaced regularly, alternately you may soak them in a chemical cleaner such as 409 or vinegar (10 percent) and water for at least an hour. After soaking, use a toothbrush or soft scrub brush to remove the built-up calcium so you may reuse the cartridge.

You can continue to reuse cartridges as long as they have not become warped or cracked. Your faucet is connected to hot water lines that are under intense pressure. Failure to shut the water main off before beginning a plumbing project will result in serious burns and damage. You can test the water to make sure it is off by turning your faucet on to see if any water comes out.How do I repair a leaking bathroom faucet? The first step in fixing a leaking bathroom faucet is to shut off the water supply and close the sink drain. Tape the jaws of the wrench to avoid putting scratches on the fixture. Remove mineral deposits on the faucet parts by using vinegar oil. The necessary tools needed for this task include a flat-head screwdriver, an adjustable wrench, replacement O-rings, washers and penetrating oil, such as CRC. How do you change a bathroom faucet? How do you replace a bathroom faucet? How do you fix a bathroom faucet? There are four kinds of faucets. Therefore, it is vital to know what kind of faucet a bathroom has before fixing the problem.

Use a wrench to loosen the nut. The stem appears after loosening the packing nut. Depending on the faucet type, the stem twists off from the valve or pops right off.Pegasus Kitchen Faucet Repair Inspect the O-ring and washer at this point since they can be the cause of the leaking faucet. Thug Life T-Shirt XsIf the washer has an issue, remove it and put the replacement on the valve seat. Toilet Bowl Wax Ring IngredientsThe replacements must be an exact fit. A homeowner can seek the help of a plumber to buy the right size of O-rings and washers for his faucet. After making sure everything is intact, reassemble all the faucet parts accordingly and then turn the knob slowly to see if the problem is resolved. How do you install a bathroom sink?

To install a bathroom sink, turn off the water supply, unscrew and remove the water lines, pull out the sink, caulk the sink hole, set the new sink inside, and reconnect the water lines. This 90-minute process requires a bucket, pliers, caulk, gloves and a wrench. How do you repair a Delta bathroom faucet? To repair your Delta bathroom faucet, identify the issue; then, purchase and install replacement parts to fix the problem. Before you begin, determine your faucet type to find the right troubleshooting guide. Delta bathroom faucets vary in design, so parts may vary from model to model. What causes a bathroom faucet to leak at the base? A leak at the base of a bathroom faucet is most likely caused by the wearing down of one of the parts inside the faucet, such as the packing material or rubber washer. Replacing these worn-out parts should solve the leaking issue. What tools are required for a Moen bathroom faucet repair? Tools required to repair a Moen bathroom faucet include screwdrivers, an adjustable wrench, pliers, a flashlight and plumber's tape.