How do I resolve most common issues I am having with the Dual Flush Valve in my toilet? How to resolve the most common issues with the Duo Flush System Toilet Converter How do I install the Duo Flush System Toilet Converter? A) Please watch this installation video on installing the system: How Do I remove the Converter from inside the tank once I have all ready installed it? A) Gently rock the converter away from the overflow pipe and pull up. B) Unhook the cable box from the toilet handle – Push the button on the top of the box and pull the cable box away from the tank. The Full and Half flush closes immediately after I try a full or half flush: A) Change the dial settings on the top of the Converter. Changing the dials to a higher setting will allow for a longer flush. B) Raise the water level. Raising the water level so that it is ½ to ¼ inch below the overflow pipe will add head pressure and a longer flush period. C) If solutions A and B do not resolve the issue call Fluidmaster’s Technical Service Department 800-631-2011.

The toilet bowl does not completely flush out the paper: A) Change the dial settings on the top of the Converter. C) Check the Refill Tube to be sure it is pointed into the Overflow Pipe. D) Disengage the Roller Clamp located on the Refill Tube so that the setting is on number 8 (flow is fully open). E)  If solutions A thru D do not resolve the issue call Fluidmaster’s Technical Service Department 800-631-2011. The Fill Valve turns on and Off (Ghost Flushing) and turns the toilet on through the day: A) Check the Refill Tube to be sure it is above the overflow pipe and hooked to the Refill Tube Clip. If the tube is inside the overflow pipe pull it out and attach to Overflow Pipe using a Refill Clip. B) Clean Drain Seat – Pull off converter from inside the tank drain and clean both the seat and the rubber seal located at the bottom of the converter.  Replace converter when clean. C) Reset Angled Seat Adaptor. Pull converter off the drain and remove the angled seat adaptor, once removed turn it upside down to locate the sealing putty.

Spread the putty around the adaptor base evenly. Replace adaptor and replace Converter back onto drain. D) If solutions A thru C do not resolve the issue or you need a Refill Clip call Fluidmaster’s Technical Service Department 800-631-2011. For questions that are not listed here please contact Fluidmaster’s Technical Service Department: Hours: 5:30 AM to 5:00 PM Monday thru Friday Solutions for a toilet fill valve that will not turn off Adjusting the water level in the toilet bowl and setting the refill rate Solutions for a Weak or Incomplete Flush (toilet bowl does not clear) after installing a Fluidmaster Toilet Repair Kit Fix your most common toilet problems fast and easy Solutions for a toilet that ghost flushes (toilet that turns on by itself)How to Adjust a Dual-Flush Toilet Brand X Pictures/Brand X Pictures/Getty Images Dual-flush toilets save money on your water bill. They have two separate buttons for flushing the toilet, depending upon the waste inside.

Liquid waste requires less water than solid waste. As with any other toilet, adjustments are occasionally necessary to ensure the toilet works properly. Adjusting a dual-flush toilet involves adjustments to the water level and the flush buttons. Fiba Asia Tickets SmMaking adjustments to the dual-flush toilet does not require removal of water from the tank. Rims And Tires Chula VistaYou will need to flush the toilet when testing your adjustments.German Shepherd Puppies For Sale In Saudi Arabia Lift the dual-flush toilet tank lid off the tank and place it upside down on a flat surface. There are two rods under the tank that connect to the push buttons. Do not bend or damage these rods. Find the float adjustment screw between the fill valve and the flush valve.

Turn the adjustment screw clockwise with a flat-head screwdriver to raise the water level to the indicator line on the inside back of the toilet tank. Turn the screw counterclockwise to lower the water level. Place the lid back over the tank and test the flush buttons. The small button is for liquid waste, and the larger button is for solid waste. Some dual-flush toilets require pushing both buttons for solid waste. Test each button to make sure the toilet flushes properly. The small button has a small flush, while the bigger button or both buttons together flush the toilet fully. Remove the lid from the tank and lay it flat upside down if adjustments are necessary. Loosen the plastic nut on the push-button rod with a wrench. Do not remove the nut; just loosen it enough to turn the rod on the push button. Turn the push-button rod clockwise to lower the rod and counterclockwise to extend the rod. Only turn the rod one full turn at a time. Tighten the plastic nut and place the lid back on the tank.

Test the flush operation again. Continue making adjustments as necessary. Sloan: Sloan Dual Flush Installation Manual American Standard: Dual Flush Owner's Manual How to Adjust a Dual-Flush Toilet. Dual-flush toilets save money on your water bill. They have two separate buttons for flushing the... How to Use Dual-Flush Toilets. A dual-flush toilet is also referred to as a high-efficiency toilet. How to Adjust a Dual-Flush... You can conserve water by installing a toilet with a push button flush valve. The push-button valve has two buttons, one for... ... or completely rebuild the toilet with new dual flush technology. How to Adjust a Dual-Flush Toilet. How Does a Dual... A cistern has several parts inside, each with a specific task. The flushing mechanism, which is usually a lever or a push-button,... How to Adjust the Water Level in a Toilet Tank. A toilet that doesn't have enough flushing power may need the water... Toilets don't operate simply on the principle of gravity in sweeping water and waste materials down plumbing pipes.