You don't have to put up with the slow drip from a leaky faucet, nor with the growing stain it often leaves in the tub or shower. Fix it now and you'll prevent those headaches and save on you water bill too. The entire job, with special tools, may set you back a bit of cash, but doing it yourself is a lot cheaper than hiring a plumber, and usually much cheaper and easier than tearing out the old faucet and installing a new one. Worn rubber washers, seals or gaskets in the valve assembly cause most leaks. Here we'll show you how to fix a stem-type valve, which is common in older, two-handle faucets (separate hot and cold). We won't cover single-handle faucets here. By the DIY experts of The Family Handyman MagazineOur systems have detected unusual traffic from your computer network. Please try your request again later. Why did this happen?Bathtub spouts may need to be replaced for a few common reasons: the diverter can get worn out so that it no longer blocks the water flow to divert the water to the showerhead

the threads that connect the spout to the pipe can corrode or crack allowing water to trickle along the pipe and drip inside the wall causing damage the finish on the spout can corrode or flake off or the finish may just need updating if you decide to change any of the other fixtures in the bathroom Replacement is usually the best option for each of those issues and it is fairly simple. Before replacing your tub spout, you will need to determine which type of tub spout you have and what kind you will need to replace it. There are two basic types of tub spouts: diverter style that allows you to send the flow of the water to either the tub spout or the shower with a diverter right on the tub spout and non-diverter style that flows only from the tub spout into the tub. Within those two types are different attachment options: slip-on with setscrew or the threaded type. A slip-on style bathtub spout will have a setscrew, which is a small screw located on the bottom of the tub spout.

The slip-fit tub spout is designed to slip onto a 1/2" copper pipe without the use of any threads. The end of the copper that will be used must be free of burrs or rough edges, when using this type of spout. A threaded tub spout will not have a setscrew, and will twist off of the nipple or pipe. This style will either be a front-end threaded tub spout or a rear-end threaded tub spout. Check out our helpful video explaining the various types of tub spouts and tricks for installation, or keep reading for more detailed instructions. View video tutorialHow To Install Tub Spouts How to Remove a Slip-On Tub Spout Quick Tips: Before turning the spout, make sure the setscrew is loosened completely. If the setscrew is still tightened onto the pipe while turning the spout, you are likely to damage the pipe coming from the wall. If it's really stubborn, you can insert a screwdriver or a wrench into the tub spout opening for leverage, and turn the spout to loosen it. However, try not to wiggle the spout and pipe because too much jarring may cause problems with the plumbing in the wall.

How to Install a Slip-On Tub Spout How to Remove a Threaded Tub Spout How to Install a Threaded Tub Spout Make sure that your new spout is the same length as your old one to avoid having to adjust the pipes or use an adapter. If you have a FRONT-END threaded spout, measure from the wall to the end of the nipple to get the appropriate size. If you have a WALL-END threaded spout, your threaded nipple should be a maximum 1/2" in length.Kidkraft Warehouse Sale If you have a TELESCOPING threaded spout, your nipple should be a maximum 1-3/8" in length.Can You Buy Six Flags Tickets At Kroger Apply approximately 4-6 wraps of PTFE thread sealing tape.Discount Tires Spokane Valley How to Remove a Brass Adapter Slip-On Style Tub Spout

How to Install a Brass Adapter (with set screw) Slip-On Style Tub Spout How to Install a Sweat/Solder Brass Adapter Style Tub Spout Clean the end of the copper tube with sandcloth or outside tube cleaning brush and the inside of the brass adapter with a 1/2" copper inside fitting brush. This is the most critical step in obtaining a leak free solder joint. Don't touch the copper pipe, or the inside of the adapter, with your hand once cleaned. How to Install a 1/2" Threaded Brass Adapter Style Tub Spout Apply thread sealant PTFE tape or pipe compound to the pipe nipple threads.On this page I will show you how to repair and rebuild a Gerber two and three handle tub and, or shower faucet. All the images are in thumbnail format, to see a larger image just click on the image. The following instructions, will also apply to other faucets with worm like steams and seats, like Price Pfister, American Standard andMake sure the water is

A word of caution: with any plumbing repair things can go wrong and you may find yourself in a situation where you have to call a plumber. you find your self in this situation please check out my list of local quality plumbing and heating companies. This is a 3 handle tub and shower faucet, The only difference between 2 handle and the 3 handle is the middle, or diverter stem is not needed. This is a set of stem wrenches, In most cases you will need this to removeYou can get them at any This is a seat removing tool for a Gerber faucet. universal seat removing tools work, but there is a risk of striping the seat with them. This is a universal handle have to have it, sometimes you The little red tin is plumbers heat proof grease. NOT USE ANY OTHER TYPE OF GREASE This faucet did not have screw caps, but if yours does, just put your finger nail under the cap and it will pop right