Your online resource for all things plumbing - for Homeowners and Plumbers AlikeHow to Replace a Bathtub Overflow Drain Gasket It is not often that your bathtub overflow gasket needs to be replaced; its lifespan is approximately 10 years. This seal prevents water from entering behind your bathtub around the overflow drain. The overflow gasket is a rubber ring that fits in the opening behind your overflow cover. By removing the cover you will have easy access to your gasket. With a few simple hand tools, you can replace your own gasket without the need to hire a plumber. Cover the bathtub drain either by closing it with the stopper or by placing a towel over it--it's all too easy to drop or knock one of the screws into the drain. Loosen and remove the two screws that are holding the overflow drain cover plate in place. The cover plate must be out of the way in order to access the gasket. Pull the cover plate off and set it aside with the screws. Use pliers to grasp the overflow gasket.

Pull straight out to remove it. If you have trouble removing the gasket, spray it with a lubricant to help loosen it.Padme Amidala Wedding Dress Costume Scrape the area behind the cover plate to remove old caulking before you install the new gasket.235/75r15 Tire Dimensions Insert the two screws that hold the cover plate into the holes in the drainpipe to push the pipe back far enough to install the new gasket. Hoover Washer Dryer FaultsThe screws do not need to be fully tightened at this point, and you do not need the cover plate for this step. Insert the new gasket into the overflow hole with the thin edge facing up. Press the gasket firmly into place, taking care not to press against your overflow pipe. Remove the screws and apply a bead of silicone caulk around the perimeter of the gasket.

Hold the cover plate in place and insert the two screws. Tighten the screws to hold the drain overflow cover plate in place. Take care not to over-tighten the screws; they only need to be tight enough to hold the cover plate. If you over-tighten the screws, you can crack the drainpipe. Plumbing Help: "How to Replace a Bathtub Drain and Overflow How Does an Overflow Drain on a Bathtub Work? How to Install a Bathtub Drain and Overflow How to Change Waste and Overflow Cover On a Bathtub How to Remove Old Gaskets How to Replace a Bathtub Faceplate How Do Bathtub Drains Work? Waste and Overflow Gasket The DANCO Waste and Overflow Gasket fits between a tub and overflow plate and provides a positive seal to help prevent leaks. This rubber gasket offers compatibility with most waste and overflow connections. The gasket offers the benefit of being entirely adjustable.O.D. x 2-1/8 in. Provides a positive seal to help prevent leaks Fits between a tub and overflow plate

Compatible with most waste and overflow connections This question is from Waste and Overflow Gasket1 I am looking for bathtub overflow gasket maden of b spongy material. I purchase one from the newport news va store b aboutba weeknago. If the trip lever on your bathtub has stopped working or if water slowly leaks down the drain when the tub is full, repairing or replacing the linkage and plunger behind the trip lever may solve the problem. Step 1: Remove the two screws from the trip lever faceplate to free the faceplate from the overflow tube. Step 2: Gently pull the face plate away from the tub. If the linkage is still attached to the backside of the face plate, the linkage and plunger should pull up and out of the overflow tube without too much difficulty. Step 3: If the linkage has broken away from the trip lever, set the face plate aside. Use a claw-type extension tool or a wire with a small hook at the end to fish the linkage and plunger out from inside the overflow tube.

Step 4: Clean the plunger and linkage with steel wool and a de-liming cleaner such as CLR or vinegar. If the plunger looks worn or the linkage is broken, replace the entire mechanism with a new assembly. Step 5: Replace the old overflow gasket with a new one. The overflow gasket is located between the back of the bathtub and the front of the overflow tube. Scrape away all remnants of the old gasket before installing the new gasket. Position the new gasket on the front of the overflow tube, with the thicker portion of the gasket toward the bottom to compensate for the slope of the tub wall. Step 6: Attach the plunger to the linkage and attach the linkage to the trip lever. The linkage is typically attached to the trip lever with a small cotter pin. Slip the pin through the back of the trip lever and bend one or both of its sides up to hold the linkage in place. Step 7: Adjust the length of the assembly by turning the threaded rod at the top of the linkage. Step 8: Feed the plunger and the linkage assembly down into the overflow tube and press the faceplate into place.

Step 9: Raise and lower the trip lever to test the functionality. Step 10: Fill the bathtub with enough water to test the seal of the plunger. Adjust the plunger height until a proper seal is achieved. Step 11: Insert and tighten the faceplate screws to complete the job.How do you know if your overflow gasket has failed? Check for a water stain on the ceiling below the bathtub. If you overfill the bathtub, the water will find this overflow drain before it finds the floor. Behind this cover is the overflow gasket, and it attaches to the drain. It creates a watertight seal that prevents leaks. These overflow gaskets loosen, crack or rot over time, and need to be replaced. Here are some tips to keep your gasket maintenance covered. Check the screws on the overflow drain cover annually to make sure the seal is snug. Check the gasket for wear and tear once a year and replace if necessary. Call a licensed plumber if the gasket or the overflow drain that the gasket attaches to spring a leak.