If a compression-type faucet continues to drip after both handles are turned to the off position, remove both handles to inspect for damage to the stem assemblies. Tip: When repairing a faucet, close the sink's stopper and cover it with a rag to prevent small parts from falling into the drain. Turn the water shut-off valves under the sink to the off position, then turn the faucet handles to the on position to drain any remaining water. Expose the Screw Holding the Handle If there is a decorative cap on top of the handle, carefully pop it off with a utility knife (Image 1) to expose the screw holding the handle in place. Remove the screw with a Phillips-head screwdriver, and pull off the handle to expose the stem assembly. (You may need to pry the handle off gently with a screwdriver. If so, pad the screwdriver with a rag to avoid damaging the faucet.) With the handle out of the way, use slip-joint pliers to remove the retaining nut that holds the stem in place (Image 2).

Inspect the stem assembly for damage. Check the rubber washer on the end. If it looks OK, unscrew the packing nut to see whether there is damage to the O-rings inside (Image 1). If the washer is damaged, remove the screw, and replace the old washer with a new one. If an O-ring is bad, cut it off with a utility knife, coat a new one with heat-proof grease, and slide the new O-ring into place on the stem, using a flat-head screwdriver as a guide (Image 2).2014 Honda Pilot Headlight Bulbs An alternative to replacing washers and rings is to replace the entire stem assembly. German Shepherd Puppies For Sale San Antonio TexasIf you decide to take this course, it's best to replace the stems on both the hot- and cold-water sides. Hankook Winter Tire Rebate

Note that because the hot- and cold-water handles often turn in opposite directions, the hot and cold stem assemblies may be different. Make sure to buy the right parts. Some are color-coded to indicate hot or cold. Check for Rough Spots If the washer and O-rings look good, use your finger to check for rough spots around the valve seat inside the faucet (Image 1). If the seat is damaged, the faucet may not make a watertight seal even with new washers. Use a specially made seat wrench to remove damaged seats and replace them (Image 2). Once repairs are complete, reassemble the faucet: drop in the repaired (or new) stem assembly and tighten the retaining nut with slip-joint pliers. Replace the handles and secure them with their screws. Replace the decorative cap. Turn the water supply back on, and check the hot- and cold-water sides to make sure they both work properly and without drips.How to Fix a Leaky Faucet There are many kinds of faucets, but chances are your leaky fixture is a compression faucet -- and it's a snap to fix.

Step 1 Tighten the nut Remove the faucet handle by unscrewing the screw that attaches it, which is often covered by a decorative cap you’ll need to carefully pry off. Using your wrench, try tightening the packing nut, which is the nut at the base of the handle’s stem. Some leaks are simply caused by a loose nut. Put a rag over the drain to catch any small parts you might drop. Step 2 Turn off water If tightening the nut doesn’t solve the problem, you might have to replace the washer. Locate the shut-off valve for the faucet you are repairing and turn off the water. The shut-off valve will most likely be beneath the sink. If not, follow the pipes until you find it. Turn the valve’s handle to the right to shut off the water. Step 3 Empty the faucet Open the faucet by twisting the top of the stem until all remaining water in the pipes flows out. Step 4 Remove the stem assembly Unscrew the packing nut to remove the entire piece that holds the stem, called the stem assembly.

Step 5 Replace the washer If your faucet has a washer on the bottom of the stem assembly, remove the screw holding it on. Replace the old washer with a new one, then tighten the screw. The correct size washer is critical; to be on the safe side, take your old one to the hardware store when buying a new one. Step 6 Wrap the nut If your faucet doesn’t have a washer, wrap the packing nut with string or wicking (available at hardware stores), which will act as a washer. Or put a thin line of plumber’s putty around the threads at the bottom of the stem assembly. Step 7 Reassemble Replace the stem assembly and tighten the packing nut. Step 8 Turn water on Attach the handle and turn the water back on by reopening the shut-off valve. Enjoy the blessed silence! Fixing a leaky faucet can save up to 20 gallons of water a day!DevonshireCapturing the elegance of a bygone era, Devonshire is reminiscent of old-world design. This Devonshire faucet brings a refined look to your bath or powder room sink, with lever handles providing easy operation.

Easy-to-clean and leak-free UltraGlide valves offer durable performance over time.Product Features:All Kohler Widespread Faucets come with handles and valves pre-assembledSpout, handles, valves, drain, tee assembly, supply lines, and attachment hardware come all in one boxFully covered under Kohler's limited lifetime faucet warrantyFaucet body constructed of brass, ensuring durability and dependabilityKohler finishes resist corrosion and tarnishing, exceeding industry standards for durabilityThe Devonshire Collection features a classic silhouette will complement a variety of bathroom decorsDouble handle operation - handles rest on 1/4 turn valvesMounts in a widespread/mini-widespread configuration - 3 holes required with handles completely separate from the spoutMetal pop-up drain assembly included for complete installationADA compliant - complies with the standards set forth by the Americans with Disabilities ActLow lead compliant - meets federal and state regulations for lead contentDesigned for use with standard U.S. plumbing connectionsWaterSense Certified product - uses at least 30% less water than standard 2.2 GPM faucets while still meeting strict performance guide linesFeatures an extra-secure mounting assemblyAll hardware needed for installation is includedProduct Technologies / Benefits

:UltraGlide Valve: Kohler has created the next generation of faucet valve technology with the Ultra-Glide ceramic valve. With high quality engineered ceramic materials, this valve is built to be exceedingly durable and ultra smooth. The Ultra-Glide is rated for up to 4,000,000 on/off cycles, beating the industry standard by eight times and guaranteeing a lifetime of leak-free performance. Unlike standard valves, the Ultra-Glide confines the water below the valve stem, keeping the majority of components dry at all times; this reduces the chance of corrosion and deterioration that affects most valves. Additionally, this valve increases the turning radius of the faucet handles, allowing for greater and more pin-point control over the water flow's volume and temperature. The Ultra-Glide valve represents the pinnacle in versatility - it will last a lifetime and bring any home into the new age of faucet technologies.WaterSense Certified Product: To help make a difference on a global scale and to further its role as an industry leader in eco-performance practices, Kohler has established partnerships with a number of environmental organizations, including WaterSense.

Many Kohler faucets and toilets are equipped with low-flow technology - they use less water, while continuing to meet superior performance standards.Quick Mount Installation: With Kohler’s innovative valve technologies, installation is now as simple as one-two-three. Simply place the faucet handle(s) in the desired position on the countertop, and the valve cartridges thread directly in from the bottom with a locking nut. All that is required is the tightening of two mounting screws. In addition to the ease of installation, this process also offers an extra-secure mounting assembly. Where most faucet handles will loosen over time, Kohler's will hold firmly in place for the life of the faucet.Product Specifications:Overall Height: 4-3/4" (measured from countertop to highest point on faucet)Spout Height: 3-3/8" (measured from countertop to spout outlet)Spout Reach: 6-3/8" (measured from center of faucet base to center of spout outlet)Mounting Type: WidespreadFlow Rate: 1.2 GPM (gallons per minute)Maximum Deck Thickness: 1-3/8"Number of Holes Required for Installation: 3Faucet Centers (Distance Between Handle Installation Holes)

: 8" - 16"2 metal lever handles are included with the faucetVariations:K-393-N4 Centerset version of this modelAbout Kohler: Gracious living is characterized by qualities of charm, good taste, generosity of spirit, and the enhancement of nature. It is Kohler's mission that you improve your sense of gracious living with every experience you have with a Kohler product or service. Kohler lives on the leading edge of design and technology, while maintaining a constant level of quality, regardless of price. It sets the standard of excellence in its field, and yet is constantly striving to improve. From sustainable products in the kitchen and bath to power systems that protect data centers and urban landscapes all over the world - this is what the Kohler company is all about.Note to consumer: This product is changing flow rate to adhere to California requirements. Shop All Kohler Devonshire Collection Products Our SKU: Kohler K-394-4 Kohler K-394-4-BX* Kohler K-394-4-G* Kohler K-394-4-BN Kohler K-394-4-2BZ Kohler K-394-4-BRZ* Kohler K-394-4-PB Kohler K-394-4-CP Kohler K-394-4-CB* Kohler K-394-4-BV Kohler K-394-4-SN

Kohler K-394-4 Devonshire Widespread Bathroom Faucet with Ultra-Glide Valve Technology - Includes Metal Pop-Up Drain Assembly Reviews - page 2 Does this come with a showerhandle for the tub? You may want to look at the K-T397-4.They were not on the Tech Spec list. Do I need to order escutcheons separately? The Kohler K-394-4 is a double handled bathroom faucet and would not have an escutcheon as those are meant to have a single hole faucet fit into a three hole sink. This item doesn't have an escutcheon designed for it. Can this faucet be installed on 3cm. thick granite? Yes, The Kohler K-394-4 can be mounted onto a deck with a maximum thickness of 3.5cm. Is the faucet low lead california compliant?The Kohler K-394-4 is Low Lead Compliant. Measurement of base of handles? The Kohler K-394-4 handles at the base are 2-1/2" in diameter. What size fitting do I need to connect the faucets to my water supply? The Kohler K-394-4 should be used with the Kohler K-7637 Angle Supply With Stop.

Can we get a four prong handle instead of the lever type? The Kohler K-394-4 is part of the Devonshire collection and not available with 4 prong (cross) handles. is there a matching set for the bath tub? The matching tub set is the Kohler K-T398-4, valve is required. What diameter is needed for the center hole? The Kohler K-394-4 Faucet requires a center hole of 2". What's the difference between the 2BZ and the BRZ in the Devonshire collection? Kohler changed their oil rubbed bronze finish some time ago so the BRZ was the old finish that is being fazed out and the 2BZ is the current finish. They differ in the fact that the 2BZ shows more of the copper undertones wherer the lines on the units appear. What's the number to order the matching pop-up drain assembly? The Kohler K-394-4 will include the matching pop-up drain assembly. Will this faucet fit a drain outlet 1 3/4" OD? Also, the 3 faucet hole measure 1 1/2"D will this faucet work with these measurements?

The Kohler K-394-4 will fit a 1 3/4 tail piece piping. The 1 1/2" is standard and will fit. Are all kohler colors the same even if you choose different product lines? Kohler finishes are the same throughout their products. Is there a tub/shower/spout that goes with this the faucet K394-4?The Kohler K-T395-4 Devonshire® Rite-Temp® pressure-balancing bath and shower faucet trim. What is the diameter of the base of the spout? The base of the Kohler K-394-4 is 3" in diameter. Is this faucet compatable with the K-2189-8 Portrait sink? The Kohler K-394-4 is just fine with that sink. Regarding the Kohler L-394-4, where do you measure to calculate the 8" spread? The faucet "spread" is measured from the center of the left handle to the center of the right handle, or more specifically, the center of the faucet hole that is drilled in your counter/sink. Will this faucet fit on a pedestal sink with a back deck width of 3 1/4 - 31/2"? The Kohler K-394-4 should fit on 3 1/4" back set as the base of the faucet is 2 1/8" deep.

Will this set work with the Memoirs sink, K2241-8? The K-394-4 will work with the K2241-8. It will reach over the drain a little, but this should not be an issue. How can I tighten a loose handle? The Kohler K-394-4 can be tightened by holding the handle and turning the bonnet counter clockwise. This will let you pull the handle off and will expose a Phillips head screw that you can use to tighten the handle. Is this for sink or bathtub? The Kohler K-394-4 is a widespread bathroom sink faucet. How do you clean hard water spots from the drain without scratching the finish? Soak a rag in vinegar, set it on the drain for 30 minutes at least, remove rag and use non-scratch sponge to clean spots, and repeat. Is there any other part required for the sink faucet? Kohler K-394-4 is going to come with all of the items that are needed for the time of installation. There are no additional items that are needing to be ordered. What is overall height of this faucet?