Replacing bath fixtures is a simple home-improvement project. Whether you're installing a new tub surround, repairing a leaky faucet or replacing your old tub faucet, you'll need to know how to remove the existing tub faucet. Tub and shower faucets consists of the hot water and cold water handles and the waterspout, along with the included stem plumbing. Removing most tub faucets is a simple project that takes just a few minutes when you follow a few easy steps. Removing a Tub Faucet:Many bathtubs don't have an individual shut-off valve, so you may need to use the main shut-off valve for your home. Bleed off any residual water in the lines by turning on both tub faucet handles. Protect the bottom of your bathtub by placing a large, old towel in the bottom and cover the tub drain to prevent debris or parts of the bathtub faucets from falling in. Remove the tub faucet spout. If the bottom side of your bathrub faucet spout is smooth, you have a twist-on spout. To remove it, insert the end of a large screwdriver into the spout from the bottom and carefully turn the spout counterclockwise to twist it off.

However, if you feel a small screw on the underside of the tub faucet, use a Phillips screwdriver to remove the screw and pull the spout toward you to remove it. Twist off the remaining connection pipe. If the tub faucet is old, the pipe may be corroded. Best Laptop For CamtasiaUse a wrench to grasp and twist the pipe counterclockwise to free it from the plumbing connection within the wall.4 Pfoten T-Shirt Remove the tub faucet handles. Flashdance T Shirt UkSome tub faucet handles merely twist off if you turn them counterclockwise. Others are secured by a screw beneath a handle cap in the center of the handle. The tub faucet handle caps may feature the manufacturer logo. Pry off the handle caps with a small flat-head screwdriver. If you're going to reuse these caps, pry very gently to keep from damaging the surface.

Remove the bath faucet handle screws with a Phillips screwdriver by twisting to the left and then pulling off the handles. What remains is the handle trim and collar, which may be in two sections, and the faucet stem beneath. Grasp the collar and twist to the left to unscrew it. If the trim piece that rests against the tub surface or the wall is attached, the entire unit will twist off. If they are separate pieces, remove the collar and then pry off the flat trim by inserting a flat-head screwdriver into the opening and prying outward. Use the wrench to twist off the interior plumbing stem.The area behind the old tub faucet may need to be cleaned or repaired, especially if water damage is present. Be sure to clean the area before installing a new tub faucet. If you're replacing just one or more parts of your tub faucet, such as the spout, make sure to purchase the identical brand to ensure a correct fit. Fontaine Bellver Oil Rubbed Bronze Roman Tub Faucet with Handheld Shower

Oil Rubbed Bronze Roman Tub Filler Faucet Moen 2-handle Roman Tub Bathroom Faucet Moen S6320BN Two-function Rainshower Brushed Nickel Showerhead Moen TS3400 'Imersion' Chrome Shower Trim Moen Chrome Two-Handle High Arc Roman Tub Faucet An ongoing discussion from 2002 through 2015 . . . Q. I would like to know if I could change my shiny brass bathroom fixtures to a bronze finish by spray painting them or using some kind of chemical to change the finish. Can I apply some kind of stripping chemical to strip off the brass and reveal the metal or is there another procedure? Q. Did you find an answer to this question? I am wanting to refinish my current bathroom hardware from "shiny chrome" to antiqued copper. I've been wondering if spray paint for metal would work? If the fixtures are solid brass (which many are) it would be possible to sand off the finish and get down to the substrate. With good polishing and buffing, this might leave an attractive dull brass color in place of the overly shiny bright brass or chrome look.

Paint does not stick real well to brass even when you use a good (and not at all without it), and this is a very high wear application, so paint doesn't really sound very promising. The ideal answer would be to send the faucets to a plating shop for real plating in the tone you prefer. But because of the issue of labor cost on onesy-twosy stuff, this is not cheap -- it probably costs as much or a little more than new mid-range faucets; If you do decide on paint, please let us know how it goes since many people ask, and we aren't able to relate many actual successes yet, although in letter 21894 Kellie J from Spring Hill, TN reported using Rustoleum brown hammered paint on her bathroom faucets. Q. I am trying to replace a bathroom tub faucet. It is brass and was custom made by the original home owners, so I cannot find any faucet to replace it unless I redid all of the plumbing. I have been able to replace all of the other fixtures with a satin nickel finish, and would like to have the same for the tub spout.

Do you know of any place that will 'dip' this brass fixture into a satin nickel finish? or a spray paint or other 'do it yourself' method of changing the finish? I'd appreciate your help. A. There is probably nothing you can do at home that will be fully satisfactory, Trina, but this item can certainly be satin nickel electroplated. Look in our Jobshops Directory or your yellow pages for a consumer friendly shop. Be aware, however, that cleaning, stripping, polishing, scratch brushing, plating, and post treating this fixture will take at least a couple of hours and that a plater can't work cheaper than a plumber or mechanic. Q. What paint can I use to repair rusting chrome bath handles? I have seen car chrome sprays written about that have excellent finishes but can't find any that are sold in UK. Would model type paints work? I'm not expecting it to look flawless.You can try a self-etch primer, followed by a chrome toned paint like Plastikote Bumper Chrome Paint. Please advise if you enjoy any success.

"Chrome" colored bumper paint Q. I have high end brass and chrome bath faucets/spouts. The brass is gold plated and wearing thin. Can they be refinished. How about PVD finishing and by whom? A. You mentioned that these are "high end". You may already know it, but replating can cost more than "low end" replacements because the labor involved in plating individual items is very different than the labor involved when hundreds of faucet sets at a time are plated by an OEM. As an alternate to gold plating, it is possible to PVD some gold colored titanium nitride either onto nickel plating or onto real gold plating for wear resistance, but PVD is done with million-dollar machines and I don't know of any shops in the titanium nitride business who do the process for consumers. Q. Hi, I am purchasing a house with a double sink. The faucets are gold toned, but I prefer satin silver or other silver tone. Can I remove these and have them refinished, without spending more than two new faucets would cost?

A. Sorry, it's unlikely that the process will meet that price point, Jenna. Q. Regarding rub n buff product. Can I use this to tone down a bright brass bathroom faucet. I've used this product before on headboards, lamps, frames, but nothing that I have to touch frequently like faucets. will this product work on faucets. Q. I have an oil rubbed bronze waterfall faucet that I used a calcium deposit removal cleaner on (the faucet lip and aerator parts). Even though I left the cleaner on only a minute or so, and thought I rinsed it well, I now have the finish coming off this faucet. I want to paint (by brush not spray) this area of the faucet and plan to make it looked antiqued in a copper color finish. What kind of primer do I need, and would a product like Rub N' Buff work on top of whatever primer you suggest. Open to all suggestions! Rub 'n Buff is a wax based product per my understanding, so would be better used on metal than on top of paint or primer. Readers have not advised us of their success or lack of success in using it on bathroom fixtures.

I'd be surprised if you found it satisfactory, but I really don't know. Q. We have a spa-type bathtub with jets. We are remodeling the bathroom and wish to use brushed nickel. We have not been able to locate the name of the brand used in the fixtures. Can you give me some possible ideas on who may have made these, whether they can be replaced, and the cost of replating to a brushed nickel? The house is approximately 25 years old. Q. I cannot replace a Roman Tub Faucet because it is behind a wall. My wife wants to go to Brushed Nickel. I can take the spout off of the old 1990s polished brass faucet. Is there a way to remove the polished brass look and turn the faucet to a brushed nickel look? Your faucet can be refinished, but it may prove difficult to get someone to take on the job. The problem is buildup of material inside the spout that can contaminate a plating bath or PVD chamber. We know this from experience. We did one refinishing job three years ago that required us to strip and re-coat the spout four times.