If a faucet still drips after you've replaced a washer, there may be something wrong with the faucet valve seat. A defective washer may have allowed the metal stem to grind against the seat and leave it uneven, or chemicals in the water may have built up a residue that now prevents the washer from fitting tightly against the valve seat. What do you do to repair a bad faucet seat? Of course, you can replace the entire faucet. Another option is to replace the seat. Removal of the old valve seat is fairly simple if you have the right tool, called a seat wrench. Insert the seat wrench into the seat and turn it counterclockwise. Once you get the old seat out, be sure the replacement seat you buy is an exact duplicate. If the valve seat is impossible to remove, insert a seat sleeve that slides into place in the old seat and provides a tight seal. What causes pipes to burst when they freeze? How to Install a Bathtub How to Install a Dishwasher How to Remove Silicone Caulking

How do you use a pipe wrench? Another option is to use a valve seat grinder, or dresser, which is an inexpensive tool that will even out a worn seat. Be careful not to use this tool too long or with too much force because the seat is made of soft metal, and you can grind too much of it away quite easily. To use a dresser, remove the faucet stem and insert the seat grinder down to the valve seat in the faucet body. Using moderate pressure, turn the tool clockwise a few times. Then clean the valve seat with a cloth to remove any metal shavings. A loose nut in a faucet's packing can be another reason for a leaky faucet. Learn what to do for this problem on the next page. Not what you're looking for? Plumbing: Tackling plumbing problems in the home can be quite daunting. Don't dismay -- the plumbing tips detailed in this article are sure to help, even if helping means advice on when to call a plumber.How to Fix Sinks, Tubs, and Drains: Plumbing issues related to sinks, tubs, and drains, can be fixed by the average homeowner...if you have some tips under your belt to help you identify and fix the problem.

Find such tips in this article.Plumbing Troubleshooting: Sometimes figuring out what's wrong with your toilet, drain, or other plumbing-related area is half the battle. Find helpful troubleshooting tips here.Plumbing Tools: You may already have many of the tools necessary for most plumbing jobs because they are the same tools used for other do-it-yourself projects. Find out about special plumbing tools, such as pipe wrenches, in this article. Danco is one of the largest plumbing repair, replacement and remodel suppliers in the home improvement industry. We are largely focused on empowering Do It Yourself consumers with affordable plumbing products and solutions which create new ...and refreshing décors for bathrooms and kitchens. Added on: July 23, 2013 In this video we start by removing the old two handle tub and shower valve from inside the wall. First we remove the handles and spout leaving the shower head in place to hold up the old shower valve and keeping it there until the new shower valve is in place this makes it easy and keeps use inline with the new installation and makes it very easy to line up the new shower head.

Now that we have the handle off its time to go around on the back side and cut into the wall or if were lucky there just may be a trap door on the back side that gives us access to the tub and shower valve from the back side. Once on the back side of the tub and shower valve we start by disconnecting the unions on the old two handle tub and shower valve. Now the part that goes up to the shower head is copper. Sand Paddle Tires AtvWhat we are going to do here is take our torch and heat the solder connection and pull the valve loose from the shower head riser pipe. Red Nose Pitbull Puppies For Sale In Cincinnati OhioNow with the old tub and shower valve out the way lets go back to the front side in the bath room. Chorkie Puppies For Sale Oklahoma

Now this was a three handle tub and shower valve so were going to have to make some adjustments to the hole in the wall in this case we will have to open the middle hole a little wider for the new single handle tub and shower valve. This is not your standard drywall (sheetrock) wall this is old and very thick no cutting this with a saw saw. What were going to do here is use a hammer and just lightly knock out pieces of the wall slow and easy. Don't worry about covering up the old holes they make a cover plate for that. We have the hole just how we won't it lets go back to the other side behind the tub and shower. What I like to do is put my new tub and shower valve to gather and solder pieces in place before I start working in the wall with it and I also remove the washers in the valve so we don't damage the washers with the hot torch and burn them up once all this is done, I take the tub and shower valve and put it into place line it up and make all the necessary connections from the back side from here I go back to the front of the valve in that bathroom and start putting all the trim on but installing the cover plate first then if you like caulk it.

► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► ► The page you requested was not found, and we have a fine guess why. If you clicked on a link to get here, the link is outdated. What can you do?Have no fear, help is near! There are many ways you can get back on track. Go back to the previous page. Use the search bar at the top of the page to search for your products. Follow these links to get you back on track! Repair & Replacement Parts All replacement parts are not created equal. When restoring a plumbing fixture or accessory to peak operation for the long haul, you need original manufacturer parts. Off-brand versions may not fit properly or may be constructed of low quality material. F.W. Webb offers a wide range of genuine manufacturer replacement parts including, but not limited to: Toilet flush levers, flush valves, float balls, fill valves and flappers