Faucets installed in granite are often individual pieces. Granite counters create instant impact in a kitchen or bathroom. The solid stone looks and feels expensive. If you are installing your own granite counter, and if you are using an undermount sink, you will need to drill the faucet holes in the granite counter prior to installing the faucet. Typically, the style of faucet mounted directly to the stone are individual faucet pieces. This means you will usually drill three or more holes in the granite to install your faucet. Place painter's tape on the granite covering the area where you want to install the faucets. Measure the sink and mark the center on the painter's tape. Measure the distance from the sink edge to the back of the counter. In most cases, the faucet will mount centered in that distance or approximately 1 to 1 1/2 inches from the edge of the sink. Find the distance center point you want and make a cross to indicate the center faucet hole. Mark the location of each additional faucet hole keeping your pieces evenly spaced apart and the same distance center from the sink edge.

Remember to account for your backsplash along the back edge of the counter. Roll plumber's putty in your hands to make a rope long enough to enclose all of your drill holes. Form the putty into a circle around the outside of your holes and press the ends of the rope together. Press the putty to the granite to form a 1/2-inch high ring. This putty ring will help hold water inside the area during the drilling process. Attach a diamond coated hole saw bit to a variable speed grinder. The bit should be sized so that your faucet pipe will fit through the hole easily. Center the bit over the cross mark on the tape and tip the bit so that it touches on the side closest to you but doesn't touch the rest of the stone. Drill, allowing the bit to cut through the tape and make a groove in the granite. Once the groove is cut, tip the bit flat gradually to cut a shallow ring. Add water to the inside of the putty ring. Continue drilling, using variable speed and allowing the bit to do the work. Pause frequently to let the bit cool down and refill the water as needed.

Lower speeds work better than high speeds in this type of drilling process. Rock the bit slightly from side to side as you get deeper into the granite until you cut all the way through. Repeat for each hole. Seal the inside edges of the faucet holes to prevent stains later. Use the same sealer that you will use on the counter after the installation is complete. Paint the sealer on with a paintbrush and allow it to dry for 12 hours. Select a long-shank style faucet and make sure the handles or features of the faucet will not hit the backsplash during use. Read the manufacturer's instructions describing how to install your faucets. Some faucets have a rubber ring seal. Look inside the faucet for a black rubber ring. If you faucet does not appear to have one, form a ring of plumber's putty and press the ring around the drilled hole in the granite. Insert the faucet through the granite hole from the top. Place the large plastic nuts that come with the kit on the faucet pipes under the base of the faucet where they emerge from the granite and screw them on to draw the faucet tight to the counter top.

If you are using putty, this will compress the putty under the edge of the faucet. Clean away the putty that shows from the outside before it dries. Tighten the plastic nuts using a long-handled basin wrench. Wrap the threaded underside faucet pipe with plumber's tape, and screw the larger headed flexible water supply hose nut onto the pipe. Teacup Pomeranian Puppies For Sale Seattle WashingtonRepeat for the second pipe. Min Pin Puppies For Sale BcSome center-handle faucets will have their own hoses already installed, along with a faucet weight to keep the retractable faucet in its housing when not in use. Patio Furniture Rt 110 FarmingdaleFollow the exact directions with the faucet model you have purchased.

Open the inlet valve to flush installation debris out of the pipes. Discharge the debris and water into a bucket. Wrap the shut-off valve pipe threaded head with plumber's tape. Attach the 3/8-inch compression nut end of the flexible water supply, matching the hot sides together and the cold sides together, and tighten with a wrench. LAUNDRY TUB FAUCETSUTILITY FAUCETS HAND HELD SHOWER MASSAGERAIN FALL SHOWER HEADSSHOWER ARMS AND ACCESSORIES Tub Fillers Adjustable 6" -16" Widespread Tub Filler Faucets. Kitchen Faucets A full line of two handle or single handle faucets, from traditional to contemporary designs, in a wide range of finishes and handle styles. We're a full-service FAUCET WHOLESALER. no matter how small or how large your FAUCET NEEDS, we've got a SOLUTION for you. After more than three decades of providing high quality faucets, we're proud to say Banner Faucets is continuing to offer a complete line of  bar, laundry tub and utility faucets, as well as hand held and rainfall shower heads and accessories including towel racks and, soap dishes and sink strainers.

Tub & Shower Faucets Two and Three Handle Sets for new construction or repair, with a variety of finishes and handles. Lavatory Faucets Classic looks with solid functionality.  Acrylic, lever, contemporary, round blade, wrist blade and single lever handles.What tools do you need to repair a Moen one-handle faucet? The tools required to repair a Moen single-handle faucet are a Phillips and a regular-headed screwdriver, an adjustable wrench, a flashlight, pliers, plumber's putty, thread seal tape and an Allen wrench. Any additional tools required to repair a Moen single-handle faucet are usually listed on the faucet's packaging. What tools are needed when installing a drain? Most Moen single-handle faucets operate using a cartridge. This cartridge, or the plastic o-rings that encircle the cartridge, are normally the causes of a dripping faucet. Remove the plastic spanner cap located on the top of the handle to access the cartridge. Pull the cartridge free of the handle.

Many times the cartridge requires a significant amount of force to remove it. Take the cartridge to a local hardware store to correctly identify a replacement. How do you remove a Delta faucet? To remove a Delta faucet, you need a screwdriver, Allen wrench, medium-size pliers and a small pipe wrench. A Delta faucet is designed with an outer handle, a cartridge assembly and an inner sleeve to ease its removal. What tools do you need to install a bathroom sink drain? Installing a new pop-up sink drain requires a 12-inch adjustable wrench, plumber's putty and a putty knife. The majority of tasks involved in the job can be done by hand without tools. However, adjustable pliers may also be useful for difficult parts. How do you install a Pegasus vessel faucet? To install a Pegasus vessel faucet, plumber's putty and a basin wrench are needed. Turn the water supply back on to check for any leaks in the system after the installation is complete. How can I repair a Kohler faucet?