The convenience of a handspray combined with a name you can trust are good reasons to keep these faucets in great working order, and you'll find all the parts you need right here. From replacement handles, cartridges, or a new hose, we've got it. Pull-Out Kitchen Faucet Replacement Parts for Price Pfister - 533 Series Loop Handle - Chrome - Replaced by #940-100A Loop Handle - Stainless Steel Retainer Ring - Replaced by 941-7110 (brass) Vacuum Breaker Cartridge - #974-035before 2005 Replacement Cartridgeafter 2005before 2010 Spray Head - Chrome Spray Head - White Pull-Out Kitchen Faucet Replacement Parts for Price Pfister - 538 Series Spray head - Chrome Hose with Washer - Black Under Counter Water Filter Quality Stainless Steel Sinks Waste King Garbage Disposers General Faucet Repair Tips Expert DIY advice on how to fix a leaky faucet in the bathroom or kitchen, including how to stop leaks and drips, and how to repair plumbing problems.

A leaky or dripping faucet is generally a sign that a part is worn and needs to be replaced— a fairly simple task. IN DEPTH: The exact repair for a water faucet depends upon which part of the faucet is dripping and, more importantly, the mechanical makeup of the faucet. There are four main types of faucets, based on their internal mechanisms: compression, disc, cartridge, and ball. Before you can fix a dripping faucet, you’ll need to determine what type it is. If the faucet has a single handle that controls both hot and cold, it is either a ball, disc, or cartridge faucet. If it has two controls, one each for hot and cold, it is probably a compression faucet, though some types of compression faucets have disc mechanisms. The best way to tell which kind of faucet you have is to disassemble it. When fixing a leaky faucet, refer to the illustrations here for the locations of washers, seals, and O-rings—drips and leaks nearly always mean these parts need replacement.

Failed washers or seals usually cause drips; to replace them, you must disassemble the faucet. Leaks around the handle usually mean that the O-rings on the stem need to be replaced or that the packing nut or adjusting ring needs to be tightened; to do this you normally just remove the handle. Compression faucets are the type most likely to drip. The washers or seals of compression faucets are repeatedly torqued down against the metal valve seats, so they eventually wear out. When they do, the result is relentless dripping that can corrode fixtures, stain sink bowls, and waste a lot of water if they are not fixed. “Washerless” is a termed used with disc, cartridge, and ball faucets because they don’t utilize the same types of compression washers. They are far less prone to drip from the spout. They too have moving parts sealed by O-rings that wear out, evidenced by leaking from the base of the faucet itself. If a compression faucet leaks from the handle, tighten the packing nut or replace the packing, which may be a washer, an O-ring, or twine wound around the compression stem.

If water drips from the spout, you’ll need to replace a washer or a corroded valve seat. Turn off the shutoff valve for that fixture, take off the faucet handle, remove the stem, and replace the worn part with one that is the same size. While you’re at it, take this opportunity to lubricate the threads of the stem with silicone grease. If you have these kinds of faucets, it pays to have on hand an inexpensive faucet repair kit, which is essentially a little box of assorted washers and O-rings.Furniture Consignment Stores Virginia Beach Va Disc faucets leak when the inlet and outlet seals wear out or when sediment builds up in the faucet inlets. T Shirt Warehouse Fresno CaDisc assemblies don’t often wear out, but sometimes the inlet and outlet seals fail. Review On Blueair Air Purifier

Turn off the shutoff valve and replace the worn seals with duplicates. Be sure to realign the seals on the bottom of the cartridge with the holes in the faucet. Cartridge faucets leak when the O-ring cushioning the cartridge stem wears out or breaks. When they drip it might mean the cartridge needs replacing. You can buy replacements at plumbing supply retailers, home improvement centers, and some hardware stores. In certain cases, they may need to be special ordered. Be sure the replacement matches the original. Ball faucets such as those made by Delta and Price Pfister drip when the inlet seals wear out and leak when the O-rings wear out or break. If the handle leaks, tighten the adjusting ring after lifting the handle off the assembly. If the handle continues to leak, replace the cap; if the spout drips, the inlet seals and springs or the ball need replacing. At the first sign of a drip, don’t torque down on a faucet in an effort to stop the drip—in most cases this will just damage the faucet.

Instead, replace the washers or seals that are failing to seal off the faucet’s flow. If you have an older faucet that is chronically leaky, consider replacing it with a new, high-quality model. I have a Price-Pfister 533 Genesis single handled kitchen faucet that turns itself off. It is impossible to run water at a low volume because the moment your hand is off the handle it shuts off. How can I fix this? Turns out they made a faucets with heavy metal handles but cheap plastic internal parts... after a few years they fail. I called up customer service, identified myself as an original owner, gave an approximate date of purchase, and was sent new parts. They sent me a new metal nut, Pfister part 941-7110 . Then, they sent a new chromed plastic handle that has less mass.How do you repair a leaking Price Pfister faucet? The repair of a leaking Price Pfister faucet begins by shutting off the main water line. Insert a drain stopper to prevent smaller parts from falling off.

Remove the faucet handle, and loosen the collar near the faucet base. Remove the entire faucet and check the O-rings inside the stem assembly and those around the collar base. Replace all worn out O-rings with new ones from the Pfister repair kit. How do you remove the handle on a Price Pfister faucet? How do you replace a Pfister cartridge? How do you fix a leaking faucet? Ensure the faucet is off before beginning the repair process. Use a drain stopper to prevent the draining of small parts and unscrew the faucet handle using an Allen wrench. Wrap a rag around the faucet collar before you start loosening it using a wrench. The rag protects the surface coating of the faucet collar against scratches during the loosening process. Unscrew the nut, retaining the stem assembly, and pull out the entire assembly. The cause of most leaking faucets is faulty O-rings, so check the O-rings inside the stem assembly and those around the collar base. Remove the O-rings found in the stem assembly and check for abrasions, marks or tears.

Replace all worn out O-rings with new ones from the Pfister repair kit. Remove the springs inside the stem assembly with needle nose pliers, and replace the worn-out springs if necessary. The final step is reassembling all parts, turning the water on and re-checking for leaks. How do you remove a stuck and corroded faucet? To remove a stuck and corroded faucet, turn off the water, clean off the corrosion and remove the faucet seat and twist off the nut. If removal tactics do not work, the nut may need to be cut off with a hacksaw. How do you use a faucet repair diagram? A faucet repair diagram is used when doing repairs on a faucet, and it lists and labels the part names as well as the numerical steps to which the parts correlate. A faucet repair diagram is generally specific to a certain brand and model of faucet and varies depending on those criteria. Who can you call to repair a broken bathroom sink faucet? Bathroom sink repair services are available through national companies such as Benjamin Franklin, as well as localized businesses such as Riley Plumbing and Heating in Connecticut, Ace Pelizon Plumbing in the San Gabriel Valley region and Allen Company in Portland, Oregon.