When the Toilet Flapper Won't CloseMonday, Jun 30, 2014 | If the Toilet Flapper won’t close the resulting symptom would be a Double Flush in the Toilet Bowl. When the “Toilet Flapper won’t close” the cause could be: (a). The toilet flapper sticks to the over flow pipe. The flapper is fixed up against the overflow pipe and not bobbing at all. (b). The flapper is being kept up by air and water coming up through the flush valve seat. Note: This is evident when the flapper is moving and floating over the seat but will not drop all the way down until the water level rises in the tank. (c). Fill valve water can push the flapper to one side or keep it open. (d). The chain is catching on the lever arm or the chain is getting tangled keeping the flapper open. (e). The lever is old and sticking. As a result it holds the flapper open. (f). The design of the toilet flapper keeps the flapper open until the tank is emptied. If ‘the flapper sticks to the over flow pipe’, use a fingernail file on the flapper frame where it touches the over flow pipe (usually above the clips that attach to the posts on the over flow pipe).

File enough of the frame so they do not touch. You can also put Vaseline on the clips as well to prohibit sticking. Mg Red Tyre DiameterFlush a few times to check.Places That Buy Broken Laptops In Charlotte Nc If ‘flapper is being kept up by the water flow from the refill” you will see bubbles coming into the tank from the drain seat Reset the angle of the water flow from the angle adapter so it hits the top inside of the over flow pipe. Catamaran Rc Boat Hulls For SaleThis will allow the stream of water to run down the wall of the pipe and allow the flapper to close. Flow from the ‘fill valve water coming into the tank can miss-align a flapper or keep it open. You can turn the shank of the fill valve, so the stream of water is diverted around the flapper area.

If the ‘chain is catching on the lever arm’ and as a result keeping the flapper open there is a fix for this condition. We recommend you use a drinking straw and cut it to 2/3rds the length of the chain. Attach the straw onto the chain. This will keep the chain from wrapping around the lever arm. The flapper will once again open and close freely. If the ‘lever is old and sticking” replace it. If you are getting a Double Flush, you may have the wrong flapper in the tank. A 3.5 gallon per flush or larger toilet, (Pre-1994) keeps the flapper open until the tank is emptied. It is likely that you need a 1.6 gallon per flush type flapper that is adjustable. 1.6 gpf flappers close before all the water drain from the tank. 0 Comments on "When the Toilet Flapper Won't Close"check the the hinges. Something may be stuck in one of them or a hinge may be bent. Tey’re height ajustable, so you can heighten both hinges equally until the flaper closes properly.check the rubber buffers, they might be worn or broken.the rear edge of the flapper may reach to far back and get blocket on the reservoire …

Edit ArticleHow to Fix a Flapper on a Toilet A toilet that constantly runs or that doesn’t flush well is a big annoyance, as well as a waste of precious and expensive water. The good news is that most flushing mechanisms are easy to fix. While toilet flushing systems can vary, most toilets use a flapper system to control the flush. Keep scrolling after the jump to learn how to check and fix a toilet flapper. Lift the top off the tank of the toilet carefully and set it somewhere where it won’t get broken. Look inside the toilet tank. You should see a white plastic tube called an overflow tube in the tank. Attached to the tube will be the flapper guides, two arms that hold either side of the rubber flapper. This sits near the bottom of the overflow tube. Attached to the guide arms is the flapper, a round piece of rubber that is supposed to fit tightly in a hole in the bottom of the tank. Attached to the top of the flapper will be a chain or metal rod.

The chain or rod is hooked to a bar at the top of the tank, which is generally attached to a mechanism on the overflow pipe near the top. There is another rod in the toilet that turns on and shuts off the flow of water into the tank. The level of water can be controlled by a float ball on a rod or by a mechanism that turns like a dial. Flush the toilet as you watch what happens inside. When you push down on the flush handle the bar at the top lifts, pulling the flapper out of the hole. The flapper floats for a moment but as the water drains out of the tank it should settle back into the hole, closing it off. After the flapper closes the hole the toilet fills with water to the top of the overflow tube, when it should stop. Replace the chain or wire on the lift bar if the flapper doesn’t lift off the hole and you can see they are unattached. Untangle any kinks in a flapper chain if it isn’t fitting back into hole after a flush. Adjust the length of the flapper chain so that it doesn’t flop into the hole with the flapper, preventing it from sealing.

There are 2 ways. Move the hook on the chain to a different hole on the bar. Move the hook on the chain further down to shorten it. The chain should be fairly straight between the flapper and the bar when the flapper is properly seated in the hole. If it's a wire, move the wire connected to a flapper to a different hole in the bar to see if that corrects the problem. Flush the toilet again to see if the problem is solved. Adjust the float adjustment screw if the flapper does fit into the hole but water rises over the overflow tube and continues to trickle over it. Turn off the water to the toilet if none of the above fixes the problem. Flush the toilet to empty the tank after the water is off. Lift the flapper and clean the edge of the hole and just inside it, first with a cloth, then lightly with a scouring pad. Turn the water back on and flush the toilet to observe your work. If the flapper ball continues to let water leak after adjustment, you will probably need to replace it.