So, you've selected or purchased the perfect new Delta® faucet for your home… now what do you do? Do you plan to install the faucet yourself, or would you rather rely upon the services of a professional plumber? For expert faucet installation, you should contact a licensed professional plumbing contractor in your area. However, if you're ready and eager to install your own faucet, Delta offers these helpful hints. If you have not done this before, we suggest that you read the general faucet installation tips below. For instructions on installing your specific faucet, please follow the Maintenance and Installation instructions that were provided with your faucet. Items You'll Need for Installation: Silicone sealant — Plumber's Putty is not generally recommended Other Tools That May Come In Handy: How to install a Pilar Faucet Installing a kitchen faucet Installing a bathroom faucet Step 1: Position the Faucet Begin installing your faucet by placing the gasket and faucet in position on the sink.

From under the sink, thread the plastic mounting nuts onto the faucet shanks. Be sure the large side of each plastic mounting nut is up. From the top of the sink, check the faucet and gasket position. From under the sink tighten the mounting nuts, making certain not to over-tighten which could damage the nuts and make them difficult to remove in the future. Step 2: Attach the Water Supply Tubes Water is typically supplied to the faucet through water-supply tubes. Wrap the threads of the water-supply valve with plumber tape. Although most plumbers use only plumber tape, some plumbing supply manufacturers also recommend using plumber's putty. Thread the water supply nut onto the shut-off valve. Tighten the nut with a wrench. Wrap the threads on the faucet shank with plumber tape, and then thread the water supply nut onto the faucet shank. Tighten the nut with a basin wrench. Step 3: Connect the Faucet Lift Rod From the top of the sink, insert the lift-rod into the faucet.

From under the sink, make sure the pivot-rod is in the down position. Insert the lift-rod into the lift-rod strap. From the top of the sink, make sure the lift-rod opens and closes the drain plug as desired.Gateway Fx Laptop Cpu Upgrade Make any needed adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.Where To Buy Skora Running Shoes If you need to connect the lift-rod strap to the pivot rod, slide one end of the spring clip onto the pivot-rod.Homes For Sale Sugar Lake Annandale Mn Make sure that both the pivot -rod and the lift-rod are in the down posittion. Insert the pivot-rod in the closest hole in the lift-rod strap. Slide the other end of the pivot-rod. Make sure the lift-rod opens and closes the drain plug as desired.

Make minor adjustments by loosening the lift-rod strap screw and repositioning the lift-rod. Make major adjustments by removing the spring clip and moving the pivot-rod to a different hole in the lift-rod strap. Step 4: Flush the Faucet Anytime you work on plumbing, filings, chips, and other debris can fall into the plumbing pipes. This debris can damage the sealing surfaces inside the faucet and cause leaks. Remove aerator and black sealing gasket above it. Before turning on the water supply, make sure the faucet handles are open (on position) in order to remove the debris without causing damage. Open both water supply valves under the sink. Allow the water to run for 15 seconds. Close the faucet handles (turn off). Make sure any debris is cleaned from the aerator screen. Getting a copy of your instructions If you need a Installation Instructions / Owner's Manual for your faucet, enter your model number under Find Support Information.

Choose your faucet from the search results and select the Installation Instructions / Owner's Manual link to view the installation sheet. If you need help while installing your Delta faucet, there are two help options available: Call us at , Monday through Friday, 8 a.m. to 5 p.m.(EST) E-mail us any time — Responses are usually provided within 24 hours.Step 1: The old solutionShow All Items Inspect the Kit Contents The shower kit includes a one-piece triangular “neo-angle” base, and wall panels that are attached directly to the wall studs. Even though the panels are made of hard plastic, they are fragile and must be handled carefully. In addition to the base and wall panels, the kit includes glass side-walls and a glass door. To assemble and install the unit, follow the directions provided by the manufacturer. Install the Floor Drain In this kit, a floor-drain strainer and connecting drain pipe must be installed before the shower base is installed (Image 1).

First, fit the neoprene gasket onto the stem of the floor-drain’s upper section and insert the stem into the base, then screw the lower section onto the stem from below the base (Image 2). Attach a PVC pipe tailpiece to the floor-drain stem, using PVC cement. After the base is in position, this tailpiece is attached to the rough-in plumbing from below (Image 2). To provide a solid, non-slip footing for the shower base, apply a 1" thick layer of drywall compound on the floor tiles or the subfloor. Embed the shower base in the compound before it dries. Install the Wall Panels The first wall panel includes the corner piece and extends to the right (Image 1). Take extra care to level and position this panel correctly because it will affect the position of the rest of the shower components. Use 1-1/2" galvanized roofing nails to fasten the first wall panel through slots provided on the panel flange. Measure the location of the showerhead pipe and valve (Image 2).

Then transfer the dimensions to the second wall panel (Image 3). Bore holes for the plumbing outlets in the second wall panel (Image 4). Use a 3/4" Forstner bit for the shower pipe hole. If required, larger holes for the shower handles can be drilled with a hole saw or expanding bit. Place scrap wood blocking under the panel to prevent the drill bit from breaking through and cracking the plastic. After the holes are drilled, position the second wall in place. This section slides into place and connects with molded plastic fittings (Image 5). Secure it to the wall studs with nails through the nailing flange, as on the first panel. Complete the Glass Enclosure Before closing in the shower, attach the shower head and operating valve (Image 1). Attach the glass panel retaining channels to the wall sections (Image 2). Secure the glass inserts in the retaining channels. Add edge trim strips if provided. Install the shower door according to the kit instructions (Image 3).