3 oz. DIY Bathtub and Tile Chip Repair Kit BATHWORKS DIY chip repair kit is great for all Bathtubs, Tub/Shower Units, Shower Basins and Tiles. The filler included dries in minutes, sands easily with water, and will last as long as the fixture. DIY chip repair Kit is extremely user friendly and will last as long as the fixture. Includes enough filler for 10 to 12 quarter size chips or gouges Includes 120 grit wet and dry sandpaper Includes step by step instructions This question is from 3 oz. DIY Bathtub and Tile Chip Repair Kit1 Will this work on a fiberglass tub? To seal a small hole? This question is from 3 oz. DIY Bathtub and Tile Chip Repair Kit0 Will this work on cast iron tub? I would like to use this to fill in some chipped areas before finishing with the Bathworks DIY kit. This question is from 3 oz. DIY Bathtub and Tile Chip Repair Kit0 Color matching?Plastic tubs are durable, but they are more prone to cracks than metal or porcelain.

Though they are the most affordable and easiest type of bathtub to install, plastic tubs also come with a downside in comparison to the more expensive ceramic, porcelain and steel tubs: They can crack due to accidents or faulty installation. Rv For Sale Owensboro KyAlthough they are designed to hold up to the weight of a human along with water, accidents can still happen to crack the tub. Standard Poodle Puppies For Sale In NzThankfully, you can patch up a small crack and keep the tub in working condition rather than spending thousands in a bathroom remodel. How Many Lumens Does A 100w Light Bulb Put OutClean the bathtub as you would normally and pay special attention to the area on top of and around the cracked area so you can ensure no debris remains to impede the bond of patch material.

Let it dry for at least 24 hours. Cover any cracks wider than 1/4 inch with a layer of fiberglass mesh that spans each side of the crack by at least a half inch. Cut the mesh to fit with a utility knife and place it over the crack. Mix up your filler material according to the manufacturer's instructions, if required. Some fillers come in caulking tubes, while others come in squeeze tubs and buckets. Read the label on your particular type if you need to mix anything up. Apply the filler material on top of the cracked area with the putty knife. If you needed mesh tape, remove it before applying a layer of filler material, then place the mesh on top of the filler and apply another layer to cover the mesh. Cover the cracks completely until excess is oozing up out of the joints. Scrape the cracks flush with the rest of the tub using the putty knife and let the mixture harden for a few hours, or according to the manufacturer's directions. Sand the surface of the patch after it has dried to smooth it over.

Use a fine-grit sandpaper to avoid scratching the surface of the tub itself. Clean away the dust with a sponge, allow it to dry and then apply any paint if desired. Things You Will Need Putty knife Patch filler Sandpaper Matching paint Fiberglass mesh Utility knife Paintbrush Tip Photo Credits Jupiterimages/Comstock/Getty Images Suggest a CorrectionUser ReviewedHow to Repair a Fiberglass Tub or Shower Fiberglass showers and bathtubs are durable, easily maintained, and attractive fixtures, but they may still be accidentally damaged. Fortunately for homeowners, there are inexpensive kits available that can be used to make repairs if this happens. Purchase a suitable kit for your shower (or bathtub). You should make sure your shower or bathtub is fiberglass before going shopping, as these instructions will not give good results on cast iron or other types of fixtures. Make sure your shower is fiberglass by tapping it with your knuckle or a wooden spoon or similar item which will not damage the finish.

A fiberglass unit will have a soft, hollow, non-metallic sound, and depending on where you tap it, may even seem flexible. Choose the appropriate color for the kit you will purchase. Most kits come with colorants (tinting products) to change the color of the product to match common colored fixtures, such as white, off white, or almond. Make sure the kit you buy comes complete with everything you need, or purchase these materials and tools separately. The following is a list of what your kit may contain: Hardener (catalyst to harden the resin) Fiberglass mesh or mat (for large or structural repairs) Sandpaper in assorted grits, from 80 grit (coarse) to 400 or 440 grit (very fine) Thickener (to stiffen the resin for vertical applications) Protective gloves resistant to the chemicals included in the kit A mixing container and stirring tool Clean the area to be repaired. Determine if the damaged area will require fiberglass cloth reinforcing.

Read the mixing and tinting instructions of the product you have purchased. Place a protective material like cardboard or heavy construction paper on the surface you will mix the material on. Measure the amount of polyester resin into the mixing container you think you will need for your repair. Add the colorant from the correct tube that came with the kit.almond Mix thickening material into the resin/colorant mixture until it is a desired consistency for your patch. Add the hardener according to the kit's instructions.settacky Mix the repair material thoroughly. Using a flat tool like a putty knife or wooden tongue depressor, scoop out some of the mixture and apply it to the damaged area.feathered Sand the patch carefully, trying not to scuff the adjacent areas.build up Mix another batch of resin and colorant to overlay the first patch, without the thickening agent. Buff the finished repair with the buffing compound provided in the kit to restore the gloss finish so it matches the original.

Clean up the area, and admire your handiwork. Before adding the hardener, place a small amount of the the tinted resin on the surface of the tub to check for color match. When cured, the resin will be slightly lighter. After getting the color match, wipe the resin off of the tub with acetone. For large holes in the floor of a tub or shower unit, use an expanding foam product to fill the cavity below the floor. This will help support the floor, preventing future cracks. Use the product according to the directions on the can, and trim or sand off any excess foam that is protruding about the finished surface. For very large repairs, a power sander may make the process much easier. Large cracks or holes will require using fiberglass reinforcing mesh or cloth, which will usually come with the kit you purchase. This may make the repair a little more difficult, and you may even want to seek help from someone who has experience using it. A power rotary tool equipped with a buffing pad will save a lot of time and effort when buffing out the finished repair.

Polyester resin products are temperature sensitive, so providing a heat source will accelerate the hardening. On the other hand, if you are concerned about having time to complete the repair before the resin solidifies, you can cool it before mixing to extend its working life. Use disposable tools and mixing containers if possible. Cleaning polyester resin requires a strong solvent like acetone, and must be done immediately after use, so usually it is not practical to do so. Acetone or other solvents are highly combustible, so be sure there are no ignition sources like water heater pilot lights in the immediate area prior to beginning the repair. Avoid using styrofoam cups or containers for mixing your materials. Acetone and related solvents will dissolve styrofoam and spill the solvents or resins onto your bathroom fixtures and floor. Use rubber or plastic gloves (usually provided with the kit) when using cleaning solvents and mixing the polyester resin. Make sure you have personal protection equipment (mask-respirator) and plenty of ventilation while doing this repair.