Multi-function Showerhead, Shower Arm, Diverter, Hose, Multi-function Handshower, Slide Bar Kit, and Rough-in-Valve � Bancroft Shower SystemHow to Replace a Diverter Valve in a Kohler K-10412 The Kohler K-10412, a single-handle kitchen sink faucet, uses a diverter to control the water flow to the spout and the sprayer. If water flows from both the sprayer and the spout at the same time, the diverter has failed. The K-10412, a faucet from Kohler's Forte line, features a high-temperature safety limit setting and a 2.2 gallon-per-minute flow rate. The K-10412 mounts in a four-hole sink and its flexible supply tubes connect to the water shut-off valves with 3/8-inch compression fittings. Turn off the two water-supply valves under the kitchen sink. Turn the valves' handles clockwise to close them. A K-10412's supply tubes connect to the valves under the sink. Lift up on the Kohler K-10412's handle to allow all remaining water in the unit to trickle out of the spout and relieve the water pressure in the faucet.

Pry the plastic cap from the rear of the handle with a slotted screwdriver to reveal the handle's set screw. Loosen the set screw with an 1/8-inch hex wrench. Turn the screw two full revolutions counterclockwise. Pull the handle off the faucet. Lift the bonnet from the faucet; if the bonnet sticks, carefully pry it up with the slotted screwdriver. Loosen the mounting nut holding the K-10412's cartridge valve in the faucet body with an adjustable wrench. Turn the adjustable wrench counterclockwise to loosen the mounting nut. Remove the mounting nut. Lift the K-10412's cartridge valve and spout off the faucet body by tugging straight up gently. Lift the old diverter out of the faucet body with needle-nose pliers. Prepare the K-10412's new diverter for installation. Push the O-rings onto each end of the new diverter, Kohler #75878. Apply a small amount of plumber's grease to each O-ring. Place the new diverter in the slot in the bottom of the faucet body so the fat end of the diverter faces the rear of the faucet body.

Inspect the O-ring on the faucet body for damage. Replace the O-ring and lubricate the O-ring with plumber's grease, if needed. Slide the spout over the K-10412's faucet body so it faces the sink's basin.Lowes French Patio Doors With Blinds Lubricate the cartridge valve with plumber's grease and slide the valve into the faucet body so the valve's handle adapter faces the front of the faucet body.Puppies For Sale In Grants Pass Oregon Slip the K-10412's mounting nut over the cartridge valve and thread the nut into the faucet body. Zzz Best Window CleaningTighten the mounting nut with the adjustable wrench. Slide the K-10412's bonnet over the mounting nut. Push the bonnet onto the faucet body. Push the faucet's handle onto the cartridge valve's handle adapter so the handle faces the front of the faucet.

Tighten the handle's set screw with the hex wrench and replace the cap.Installation and Care Guide K-10412; Kohler: Forte Kitchen Sink Faucet K-10412 411 Plumb: Kohler Forte Faucet Troubleshooting & Repair Guide Even then, they may not carry parts for the oldest Kohler faucets. Here are a few steps to help you find original... How do I Replace a Kohler Faucet Cartridge?. How to Replace a Diverter Valve...The Kohler K-10412, a single-handle kitchen sink faucet, ... How to Replace a Kohler Shower Valve. Whether you have an older Kohler shower faucet or a newer model, ... Instructions to Repair a Kohler Kitchen Faucet. How to Repair a Kohler Forte Faucet; How to Take Apart a Kohler Faucet... How to Unclog a Diverter Valve in Kitchen Faucet How to Fix a Kohler Sink Sprayer Kohler Faucet Installation Instructions Shower Diverter Valve ProblemsCost to Install a Shower FaucetUpdated: June 2016 Shower Faucet Installation Cost CalculatorZip Code Faucets

Shower Faucet Labor - Basic Shower Faucet Materials and Supplies Totals - Cost to Install Shower Faucet - Get an INSTANT, detailed estimate of the cost to Install a Shower Faucet! Our free calculator uses up-to-date, trusted data to estimate typical subcontractor costs for a Shower Faucet Installation project. For a basic 1 faucet project in zip code 47474, the benchmark cost to Install a Shower Faucet ranges between $441.83 - $745.59 per faucet. Cost to Install a Shower Faucet - Notes and General InformationExplore the full range of shower faucet new installation labor options and material prices here. Costs to prepare the worksite for Shower Faucet Installation, including costs to protect existing structure(s), finishes, materials and components. Labor setup time, mobilization time and minimum hourly charges that are commonly included for small Shower Faucet Installation jobs. General contractor overhead and markup for organizing and supervising the Shower Faucet Installation.

Cost to Install a Shower Faucet - References Shower Faucet Installation - Average Cost Per FaucetTo lower Shower Faucet Installation costs: combine related projects, minimize options/extras and be flexible about project scheduling.While there may seem to be a wide variety of shower diverter valves, there are only 3 main types of these useful devices. If you have visited a friend's house or hotel, you might have noticed all the different kinds of shower diverter valves. The shower diverter valve can be located between the faucet and the spout, it can form the center of the faucet or it can be a vertical pull arm on the tub spout itself. The shower diverter valve enables the shower to be installed over the tub, eliminating the need for a separate shower stall or enclosure. This saves space in the bathroom avoiding the installation of extra piping, faucets, and tiling. A rubber washer is usually responsible for cutting off the water flow to the tub and forcing it vertically through the shower head instead.

This type of diverter, located between the taps on a two-tap faucet, can bring water to both the shower and the tub. The hot and cold water taps are turned on to mix the water to the correct temperature. Usually, turning the diverter clockwise 180º allows the properly mixed water to flow out through the shower head. Turning the diverter counter-clockwise will return the water flow to the tub. As in the 3-valve diverter, the bather runs water through the tub spout until it is blended to the desired temperature. The diverter, with 2 valves each in the shape of an L, pushes the water upward to the shower arm and out the shower head. This 2-valve diverter can be located in the center of a faucet that adjusts temperature with a single dial turned to the left for hot water and to the right for cold, or it can be set between the taps of a 2-tap faucet. The tee diverter is a single-valve diverter, located in the tub spout. The bather runs the water to the temperature he or she prefers, and then pulls up the diverter pull arm in the tub spout.