Hollow Door and Drywall Anchors (4-Pack) Self-drilling for efficient installation Special thread design ensures secure hold in door panels Easy installation and removal The E-Z Ancor 1-1/4 in. Hollow Door and Drywall Anchors (4-Pack) are ideal for use in hollow core doors and drywall. These zinc die-cast anchors offer a holding strength of up to 40 lb. No pre-drilling necessary in drywall. E-Z Ancor Hollow Door Anchors drill anywhere in hollow core doors and drywall, even if you hit a wood stud. Ideal for fastening applications in hollow core doors and drywall Great for hanging towel racks, hooks, pictures, and more Installs anywhere in hollow core doors or drywall Anchor will not break if it hits a wood stud Use in 1/2 in. or 5/8 in. drywall Supports up to 40 lb. in 1/2 in. drywall 40 lb. weight capacity is for items hung flush to wall and may be less for those hung out from wall Self-drilling - no pre-drilling necessary in drywall

Do not over tighten anchor Special thread design grips door panels for a superior hold Zinc die-cast design for maximum durability A superior alternative to traditional plastic plugs and mollies Can be easily removed Do not use for ceiling applications Do not use for mounting televisions This question is from 1-1/4 in. Hollow Door and Drywall Anchors (4-Pack)2 Can also be used in drywall? Also, where are your products made?Hollow Door and Drywall Anchors (4-Pack)1 Where can I get the hook in the video? Your installation video is great, however, I, the nice one-screw, sliding cover to hide screw hook is not available at Home Depot. Where can I find it?Hollow Door and Drywall Anchors (4-Pack)1 What size screw do these use? I am installing a 3/4" rail to the back of the door and would like to buy a longer, compatible screw to make the installation more secure.Hollow Door and Drywall Anchors (4-Pack)1 Is the weight rating of 40 pounds per anchor?

For example 4 anchors would add up to 160 pounds.THE typical towel bar consists of a single bar running between two escutcheons that project from the wall surface. Usually, the escutcheons are not bolted directly to the wall surface but are attached to anchor plates. The anchor plates are bolted to the wall and the escutcheons are fastened to them with hidden set screws. This mounting technique conceals the large screw heads that hold the unit in place.Best Laptop For Mechatronics The technique for mounting a towel bar to a wall depends upon the type of wall. Puppies For Sale In Fayetteville GaOnly when you know what the wall is made of -- drywall, hollow-core door or ceramic tile -- can you choose the proper fasteners and installation technique required.Cork Flooring Lowes Price

Drywall is a common wall material in modern homes and is one of the most difficult materials to get a towel bar securely fastened to. That is because drywall is made of gypsum plaster and is too soft to hold screws. If the towel bar is the right length you may be able to mount one, or both of the escutcheons directly to the wall studs behind the drywall. Use one-and three-quarters-inch drywall screws to mount the anchor plates. No need to drill pilot holes, just position the plates and use a power screwdriver to drive the screws through the drywall into the wood studs. If you cannot mount the anchor plates to the studs, you will have to secure them to the drywall. The standard hollow-wall fastener is called a toggle bolt. These fasteners have spring-loaded wings that open in the cavity behind the wall. First, you must drill a hole in the drywall that is large enough to push the wings through. Place the anchor plate on the bolt, then thread the wing mechanism onto the end.

Push the wings through the hole and tighten the bolt. As the bolt tightens, it pulls the open wing mechanism against the backside of the wall to hold the anchor plate in place. Another fastener that works well on drywall is the E-Z toggle. It has two pieces -- a screw-in toggle that penetrates through the wall and a retaining screw that screws into the toggle. This fastener is easier to use than the traditional hollow-wall fastener because you don't have to drill a hole to install it. Select the location for the anchor plate (it cannot be over a wall stud) and use a No. 2 Phillips screwdriver to twist the toggle into the wall until the end flange is flush with the wall surface. As the toggle passes through the drywall, a pivot bar opens out in the wall cavity. Position the anchor plate over the hole in the toggle flange and drive the retaining screw in place. As the screw twists into the toggle, it will pull the pivot bar tight against the backside of the drywall. The technique for mounting a towel bar onto a hollow-core door is similar to that for drywall.

The fastener to use is a hollow-wall expansion bolt called a molly anchor. Since hollow doors have thin panels of wood covering the hollow core, you will have to choose a molly anchor made especially for hollow-doors. Start by drilling a quarter-inch hole at the desired location in the door. Be careful not to exert too much pressure or you will drill through to the other side. Insert the fastener into the hole and tap it with a hammer to set it into the wood surface. Tighten the bolt in the fastener. This will cause the fastener to expand against the back of the surface. Put it through the anchor plate then drive it into the fastener attached to the door. The toughest part of mounting a towel bar onto a wall faced with ceramic tile is drilling holes through the tile without cracking it, but the holes are needed in order to attach the anchor plate to the surface. The best type of bit for drilling tile is a glass/tile bit, not a masonry bit. Mark the locations for the holes and start drilling slowly while maintaining a firm grip on the drill to keep the bit from wandering off the marks.