Tub Spout Repair Diverter

How do you repair a shower diverter valve? To repair a leaky shower diverter valve, it is necessary to replace the part. Replacing the valve is not an expensive or difficult project, and it is not necessary to turn off the main water supply. How does a shower diverter valve work? The first thing to do is to find out what type of attachment the spout has. If there is a small hole or screw under the spout, cover the drain, and then use an Allen wrench, sometimes known as a hex key, to take the screw out. The cover on the drain catches the screw before it falls into the drain. Twist the spout while pulling it straight out off the supply pipe. If there is not a set screw, it means there is an attachment between the supply pipe and spout. Take a pipe wrench, grab the spout, and then turn it counterclockwise until the spout is removed. Take the spout to the hardware store, and get a new spout that attaches in the same manner. Use caution when choosing a new threaded spout because some connect near the outlet, but others connect near the base.
The new spout must have the same connection as the old one. To install the new spout, simply reverse the steps it took to remove the old spout. Replace a bathroom shower diverter valve on the tub spout by replacing the spout. Determine if the old spout is threaded onto the pipe or attached in another way by looking for a set screw. If no screw is present, use a pipe wrench around the spout or insert a small hammer handle into the end of the spout for leverage and turn to unscrew it. If there is a set screw, use the appropriate tool to loosen it. How do you detect a leak underground? What color toilets are available from TOTO? What are helpful tips about repairing a ball valve? What are some common repairs for an American Standard faucet? What are PEX underground water lines? Is it possible to get the Moen shower faucet manual for free? With their simple, traditional designs, Forté faucets tastefully complement a variety of decor styles. This bath spout features a sleek, rounded silhouette and a sculpted design that coordinates well with other Forté accessories.
The lift rod allows you to divert water flow to a showerhead. FeaturesDiverter spout with 1/2-inch NPT connection.For bath and shower faucets with sculpted lever handle.Coordinates with the Forté collection of faucets and accessories.View more Bathtub Spouts > Lift Gate and Diverter Tub Spout Kit Kit to repair a diverter tub spout. lift gate & handleused to repair {"afterScroll":"","unitSize":155,"scrollSpeed":500,"widgetClass":"SnapToScrollerWidget","snapClosest":true,"direction":"horizontal","bindings":{"bind0":{"element":"#_widget2111964034005_trigger","type":"scrollend","fn":" \t\t\t\tfunction(event, pageNum) { \t\t\t\t\tPagedDataSetFilmstripLoaderWidget.loadPage(\'#SameCategory\', Math.floor(pageNum)); \t\t\t\t} \t\t\t"}},"beforeScroll":"","animateScroll":"true","scrollAmount":155} {"imageThreshold":3,"dataModel":{"subCategoryId":"1283","cacheEntitiesInRequest":false,"isRecentlyViewedItem":true,"imageHeight":150,"dataProviderWidget":"com.fry.ocpsdk.widget.catalog.dataproviders.SameCategoryDataProviderWidget","direction":"horizontal","itemViewerWidget":"com.fry.starter.widget.viewers.ItemViewerWithQuickLookWidget","storeSourceCode":"","imageWidth":150},"widgetClass":"PagedDataSetFilmstripLoaderWidget","emptyItemViewer":"
<\/div>
<\/div>
<\/div> <\/div> ","direction":"horizontal","loadThreshold":1,"pages":5,"pageSize":5}
Quicklook > .trigger\", newItems).bind(\"quicklookselected\", function(event, source, x, y) { OverlayWidget.show(\'#_widget2111964034121\', event, source, x, y); }); } "}},"effectOnHide":"fade","effectOnShowOptions":"{}","effectOnHideOptions":"{}","closeOnBackgroundClick":true,"effectOnShowSpeed":"","onScreenPadding":10,"allowOffScreenOverlay":false,"captureClicks":true,"effectOnShow":"fade","effectOnHideSpeed":"1200"}Homes For Sale Lake Timberline MissouriSep. 1 and Wed. Sep. 7Used Tires For Sale In Paducah Ky A tub spout may be screwed onto a threaded pipe or anchored to a nonthreaded pipe with a setscrew. Discount Tire OshkoshBefore you start to unscrew a spout, check underneath to see if there is a setscrew. If water seeps from behind the spout, it may be attached to a threaded pipe that is loose.
Remove the pipe, wrap its threads with pipe-thread tape, and use a pipe wrench to tighten it. If possible, spend a little more for a brass spout. It will last longer than a bargain-bin spout, which may be made of thin metal or even plastic that wears and stains quickly. Screwdrivers, hex wrench, groove-joint pliers, pipe wrench, caulk gun Unscrewing and reinstalling a spout There is no need to shut off the water; place a towel in the bottom of the tub to catch any debris or caulk New spout, pipe-thread tape, tub-and-tile caulk Use groove-joint pliers or a pipe wrench to remove an old spout that is threaded on. Clean the end of the pipe and scrape away any caulk on the wall. Wrap the pipe threads clockwise with two or three turns of pipe-thread tape. Screw on the new spout by hand. Wrap masking tape or a cloth around the spout, or wrap electrician's tape around the jaws of groove-joint pliers, and tighten the spout firmly. If the pipe is copper, avoid overtightening, which can strip the threads.
Some spouts attach with a setscrew. Loosen the screw with a hex wrench and slide off the spout.Replacing a tub diverter is an easy job in most cases. There are those exceptions, however. The tub diverter should have been caulked in place where the rear of the spout meets the shower wall. Cut that caulking free with a sharp knife being careful to avoid cutting the shower wall surface. Usually, you can score the caulking or lift up an edge and then peel the rest off. If someone has caulked the spout with silicone caulk you may need to exercise patience in removing it. Silicone caulk is very difficult to remove. Use a very sharp knife to cut away at it. Feel the underneath side of the tub spout. If there is an opening at the rear of the spout where it meets the shower wall, you will need to loosen an allen screw up inside that opening. The best tool to do this with is a balldriver allen wrench.  This is an allen wrench that has a ball-like tip. That allows you to tilt the allen wrench at an angle and still loosen the allen set screw.
After fully loosening the set screw, turn the tub spout gently to break the seal and pull it toward you to remove it. Install a new tub diverter spout with the same style connection, i.e, an allen set screw at the rear. Hold the diverter spout firmly against the shower wall or as far as it will go while tightening the setscrew. You can tighten the setscrew about hand tight with the spout turned 90 degrees to one side so you can get to the setscrew easily. Then turn the spout so it faces down into the tub and tighten the setscrew the rest of the way. If there is no opening at the bottom rear of the tub spout then the tub spout unscrews from a nipple. Place the handle of a pair of pliers or channellocks into the spout opening and turn it counterclockwise. If you are going to throw the tub spout away just grab the end of the spout with a pair of channellock or waterpump pliers or even a pipe wrench and unscrew it. Sometimes corrosion has totally locked the spout in place and you will have to exert quite a bit of force to remove it.
In doing so, you might damage the threaded spout nipple. If you have to replace it and can’t get a wrench on it to unscrew it, use a nipple extractor that you can buy at any hardware store or plumbing outlet. Apply joint compound to the threads of the new nipple and screw it into place using the nipple extractor to tighten it, if necessary. Apply joint compound to the external threads of the spout end of the nipple and install the tub spout. Be sure to caulk it where it meets the shower wall. Trim the acrylic latex caulk with silicone with a wet finger tip or a caulk trim tool. Let the caulk dry at least 24 hours before getting it wet. A note of caution: The tub spout nipple fitting should have been anchored inside the wall to supporting lumber but not all are. Use extreme caution when removing the old tub diverter spout or tub spout nipple. If you think the fitting in the wall is loose or not supported at all, or suspect the nipple fitting or its connections in the wall have been damaged, you must open up the shower wall to repair or replace it.